GB
- 23 -
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched o
ff
and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
•
The equipment has to be set up where it can
stand securely.
•
Before starting work, firmly screw the grin-
ding/sanding machine to the workbench or
equivalent using the 4 mounting holes (8) in
the base plate (9).
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
The grinding and polishing wheel must rotate
freely.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the equipment to the power supply.
5.1 Assembling the spark de
fl
ector / safety
window (Fig. 3/4)
•
Fasten the spark deflector (3) to the machine
(Fig. 3).
•
Use the recessed head screw (14) and (15)
to do so.
•
Tighten the screw connection using a crosstip
screwdriver and size 7 wrench. Important! Not
supplied.
•
Fit the safety window (2) to the spark deflec-
tor (3) using the lock bolt (16), washer (17),
spring washer (18) and locking knob (19)
(Fig. 4).
5.2 Adjusting the spark re
fl
ector (Fig. 5)
•
The spark deflector (3) can be adjusted in the
vertical direction using the slots in the spark
deflector.
•
To do this, slacken the recessed head screws
(14) and move the spark deflector so that it is
as close as possible to the grinding/sanding
wheel (5) / polishing wheel (6).
•
Warning! The gap between the grinding/
sanding wheel (5) / polishing wheel (6) and
the spark deflector (3) must be set so that it
is as small as possible and certainly does not
exceed 2 mm.
•
Then secure the spark deflector (3) again.
•
Warning! Adjust the spark deflector (3) peri-
odically to compensate for wear on the grin-
ding/sanding wheel (5) / polishing wheel (6).
5.3 Fitting the workpiece support (Fig. 6)
•
Fit the workpiece support (7) to the machine.
•
Warning! The angled surface of the workpie-
ce support must face away from the grinding/
sanding wheel (5) / polishing wheel (6)!
•
To do this, washer (20), spring washer (21)
and locking screw (22).
5.4 Adjusting the workpiece support (Fig. 7)
•
The workpiece support (7) can be adjusted
in the horizontal direction using the slot in the
workpiece support.
•
To do this, slacken the locking screw (22) and
move the workpiece support (7) so that it is
as close as possible to the grinding/sanding
wheel (5) / polishing wheel (6).
•
Warning! The gap between the grinding/san-
ding wheel (5) / polishing wheel (6) and the
workpiece support (7) must be set so that it
is as small as possible and certainly does not
exceed 2 mm.
•
Then secure the workpiece support (7) again
with the locking screw (22).
Anl_TC-XG_75_Kit_SPK9.indb 23
Anl_TC-XG_75_Kit_SPK9.indb 23
13.07.2020 13:05:44
13.07.2020 13:05:44
