EN
- 11 -
Air regulator (Fig. 2/Item 27)
The air regulator (27) can be
fi
tted between the
suction hose (10) and the suction tube (11).
The suction power of the nozzle can be in
fi
nitely
adjusted using the air regulator (27).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain o
ff
the equipment
when vacuuming liquids.
5.4 Suction nozzles
Combination nozzle (Fig. 2)
The dual-purpose nozzle (12) is for vacuuming
solids and liquids over medium to large areas.
Crevice nozzle (Fig. 2)
The crevice nozzle (16) is designed for
vacuuming solids and liquids in corners, edges
and other areas that are di
ffi
cult to access.
Upholstery nozzle (Fig. 2)
The upholstery nozzle (23) is specially designed
for vacuuming solids on upholstery and carpets.
Fitting the battery (Fig. 16)
Flip up the battery cover (19) as shown in Figure
16. Slot the two rechargeable batteries into the
mounts.
6. Operation
6.1 On/O
ff
switch (Fig. 1/Item 2)
Switch position 0: O
ff
Switch position I: Vacuum setting 1
Switch position II: Vacuum setting 2
6.2 Dry vacuuming
Use the pleated
fi
lter (18) for dry vacuuming
(see point 5.2). The dirt bag (14) can be
fi
tted in
addition when removing particularly stubborn dirt
(see point 5.3).
Always ensure that the
fi
lters are securely seated.
6.3 Wet vacuuming
For wet-vacuuming, use the foam
fi
lter (15) (see
point 5.2).
Check that the
fi
lter is securely seated at all times.
Water drain screw (Fig.1)
To make the tank (7) easier to empty after wet
vacuuming, it is
fi
tted with a water drain screw
(17).
Open the water drain screw (17) by turning it anti-
clockwise and drain the liquid.
When wet-vacuuming, the
fl
oating safety switch
(Fig. 4/Item 5) closes when the maximum tank
level is reached. At the same time, the suction
noise of the equipment will change and become
louder.
You must then switch o
ff
the equipment and
empty the tank.
Danger!
The wet/dry vacuum is not suitable for the
vacuuming of combustible liquids. For wet
vacuuming, use only the supplied foam
fi
lter.
6.4 Blowing
Connect the suction hose (10) to the blow
connector (9) on the wet/dry vacuum.
6.5 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.6 Battery capacity indicator (Fig. 21 / item
39)
Press the battery capacity indicator switch (40).
The battery capacity indicator (39) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED
fl
ashing:
The battery is empty, recharge the battery.
All LEDs
fl
ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
Anl_TE_VC_36_30_Li_S_USA_SPK7.indb 11
Anl_TE_VC_36_30_Li_S_USA_SPK7.indb 11
08.05.2019 10:28:15
08.05.2019 10:28:15
