Eiki LC-WB42N, Service Manual

Page: 44 / 132

-44-
Electrical Adjustments
Group/
Item
Item Name Function Initial range Note
5 Eco Fan5 Max(LAMP1) - - 0-255
Group
255
Fan Start/cooling Setting
0 Fan1 Initial Volt
Fan Start Voltage (0.1V)
60 0-145
1 Fan2 Initial Volt 60 0-145
2 Fan Initial Volt 60 0-145
Fan4 Initial Volt - 0-255
4 Fan5 Initial Volt Fan Voltage at Power Off (0.1V) - 0-255
5 Fan6-8 Initial Duty - 0-255
6 Fan8 Initial Volt - 0-255
8 Cooling Time L1
Cooling Time stting at Fan Mode L1 (x
0 sec)
1: 0, : 90, 15: 450 sec.
1-15
9 Cooling Time L2
Cooling Time stting at Fan Mode L2 (x
0 sec)
1: 0, : 90, 15: 450 sec.
4 1-15
10 Temp Error Cooling Time
Cooling Time setting at Temp Erro (x
0 sec)
1-15
11 OnStart Cooling Start Thresh-
old
60 0-100
12 After shutdown cooling Cooling after shutdown (0: No, 1: Yes) 1 0-1
Group
256
Fan Lamp Voltage down Setting
0 Lamp Voltage
Current Lamp Voltage (0.1V)(Read
only)
- 0-255
1 Lamp Vol Threshold
Threshold to judge Lamp Voltage
Down ( V×10)
0 0-90
2 Fan1 Speed Gain
Additional Fan Speed of Min at Lamp
Voltage Down (unit: 0.1V)
0 0-255
Fan2 Speed Gain 00 0-255
4 Fan Speed Gain 00 0-255
5 Fan4 Speed Gain 00 0-255
Group
257
Fan dimmer Setting
0 Dimmer Average Check
Period
Dimmer Avarage measurement Time
(0:10sec, 1:0sec, 2:6sec,
90sec...10:00sec)
1 0-10
1 Dimmer Average Dimmer Avarage Value (Read only) - -
2 Last Voltage Difference - -
Voltate Difference Goal
Group
258
Fan Ic temp for Netowrk model
0 Standby
Cooling Check
Cycle
Temp A check cycle at Standby 5 0-100
1 Standby
Cooling Start
Threshold
Cooling start threshold temp A 46 0-100
2 Standby Cooling Enable Cooling in standby Enable 1 0-1
Group
259
Fan Press Setting
0 Press Ssource Range Low - 0-102
1 Press Ssource Range High - 0-102
2 Press Fan Add Range
High(Lamp In)
- 0-5000
Press Fan Add Range
Low(Lamp In)
- 0-5000
4 Press Fan Add Range
High(No Lamp In)
- 0-5000
5 Press Fan Add Range Low
(No Lamp In)
- 05000
Group
260
Auto calibration (commn) * Auto calibration
0 Execute Calibration 0 0 - 1
Executes Auto-Calibration when
changiing the Value (PC White
100%)
1 Loop Count
Maximum Execution Times (OFFSET-
>GAIN)
8 1 - 0
2 Auto Status
Result of Auto-Calibration (Last
Memory)
0 0 / 1 / 9
0: OK, 1: Adjusting,9: Error *
ReadOnly
AutoWait Wait Value for each setting 1 - 20
4 CHECK -Tolelance Torelance of OFFSET 4 1 - 255
5 Time out wait Time out waiting time(sec) 20 1-255