EICKMEYER EickView 50 Cleaning And Instruction Manual Download Page 11

Page: 11 / 16

6. Cleaning and Sterilization

- Before and after each use, clean, disinfect and sterilize the videoscope.

- Before the disinfection or sterilization, Portable VET Vbideoscope should be cleaned

carefully.

- When finish using the device, ensure the power is off, take off the 3.5” LCD from the

videoscope. Please use alcohol or neutral detergent to make wipe disinfect for LCD.

- Do not wash SD card. If necessary, clean the SD card with alcohol cotton.

Disinfected solution must be clearly indicated suitable for endoscopes.

Note

- Before cleaning, ensure the sealing of videoscope. Do not install the vent cover.

- After using the videoscope, please clean it immediately. Do not use any cloth or tools

which can damage any surfaces of the device.

Cleaning Brush

- There are two methods of disinfection for the portable VET videoscope :

1. Gas disinfection

It should be checked carefully if the vent cover is installed well, to ensure the airiness of

internal and external videoscope.

Install Vent Cover

Summary of Contents for EickView 50

















Search results

Summary of Contents for EickView 50

Reviews:

Related manuals for EickView 50

Brands by name

Popular brands

EICKMEYER EickView 50, Cleaning And Instruction Manual

Search results

Summary of Contents for EickView 50

Reviews:

Related manuals for EickView 50

Brands by name

Popular brands