background image

 

Shanghai Ehong Technologies Inc

 

 

EH-MC10 

 

 

Bluetooth® technology

 low energy 

module 

 

 

                                                                                                           

 

 Bluetooth® radio

 

Fully embedded Bluetooth® v4.0 single mode 

TX power +6 dbm,-92.5dbm RX sensitivity 

128-bit encryption security 

Range up to 100m 

Integrated chip antenna or U.FL port 

Multipoint capability(2devices at master) 

 Support profiles 

BLE (Master and slave) 

The generic attribute profile (GATT) 

Health care, Sports and fitness, Proximity 
sensing profiles 

Alerts and timer profiles 

• 

User interface

 

  Send AT command over UART 

-   Firmware upgrade over the air (OTA) 

-   Transmit data: 300kbps transmission speed 

(UART) 

-   I2C interface(Master ) 

-    SPI  

-    PWM(4 channel)

 

• General I/O 

10 general purpose I/Os 

3  analogue I/O (10bit ADC) 

•   FCC and Bluetooth® qualified 

•   Single voltage supply: 3.3V typical 

•   Small form factor: 17.70 x 11.95x 2.2mm 

•   Operating temperature range: -30 °C to 80 °C 

 

 

Version 2.0 

                                                                                                                          July 21 2014 

 
 
 

Summary of Contents for EH-MC10

















Reviews: