background image

56 VOLT LITHIUM-ION CORDLESS MOWER — LM1700E

13

EN

To Start (Fig. L)

1)  Attach the battery pack to the mower, insert the safety 

key into the key slot and close the battery cover (Fig. I).

2)  According to Fig. L, depress the safety button down.
3)  With the safety button depressed, pull the bail switch 

upward to meet the handle and release the safety 
button.

To Stop (Fig. M)

1)  Fully release the bail switch.
2)  The electric brake in the automatic braking 

mechanism will stop the blade rotation within 3 
seconds of the bail switch release.

LED HEADLIGHTS (Fig. A-11)

Press the switch button 1S (Fig. B-20) to turn on/off the LED 
headlights in the front of the battery compartment.

FULL-GRASS INDICATOR (Fig. N & O)

THE GRASS BAG IS NOT FULL (Fig. N). 
THE GRASS BAG IS FULL (Fig. O). Stop the mower and 
remove the battery pack, clean your grass bag.

POWER INDICATOR ON THE MOWER (Fig. P)

The mower is equipped with a power indicator to indicate 
the charge status of the battery pack and the working 
status of the mower. The power indicator will illuminate 
when the blade is rotating or when the LED headlights are 
turned on.
Fig. P parts description see below:

P-1

Power indicator

Power 
Indicator on 
Mower

Meaning

Action

Shining green

Mower is working 
properly

N/A

Flashing green

Handle-Locking 
Clamp/Quick-Ad-
just Lever is not 
triggered properly

Re-triggered the 
handle-locking 
clamp/quick-adjust 
Lever

Flashing red

The battery is 
depleted

Stop the mower and 
charge the battery 
pack

Shining 
orange

The mower is 
overheated

Remove the battery 
from the mower, 
move them to the
shade and cool 
them at least 15 
minutes

Flashing 
orange

The mower is 
overloaded

Slow down your 
pace or raise up 
the cut height to 
decrease the load 

Red and 
green flashing 
alternately

Communication 
timeout

Connect EGO

MOWER OVERLOAD PROTECTION

To prevent overload conditions, do not try to remove too 

much grass at one time. Slow down your cutting pace or 

raise the cut height.
Your mower has built-in overload circuit protection. When 

the mower is overloaded, the motor will stop and the 

power indicator on the mower will flash orange. Remove 

the battery pack from the mower. Check to see if grass 

has collected beneath the deck and clear it if necessary, 
then install the battery and restart the mower. 

BATTERY HIGH TEMPERATURE PROTECTION

If the battery temperature exceeds 70°C during operation, 

the protection circuit will immediately turn off the mower to 

protect the battery pack from damage. The power indicator 

on the mower will shine orange and the LED on the battery 

will flash orange. Release the bail handle, wait until the 

battery pack cools down to approximately 67°C, then 
restart the mower.

MAINTENANCE

 WARNING: 

To avoid serious personal injury, 

always remove the safety key from the mower before 

cleaning, performing any maintenance or transporting 

the mower

.

 WARNING: 

When servicing, use only identical 

replacement parts. Use of any other parts may create 

a hazard or cause product damage. To ensure safety 

and reliability, all repairs and replacements should be 

performed by a qualified service technician

.

GENERAL MAINTENANCE

 WARNING: 

Always remove the safety key and 

battery pack when servicing or transporting the mower.

The underside of mower deck should be cleaned after each 

use, as grass clippings, leaves, dirt and other debris will 

accumulate.
Remove any build-up of grass on or around the motor fan 

(do not use water). Wipe the mower clean with a damp 

cloth.

Summary of Contents for LM1700E

















Reviews: