Edwards D395-90-000 Instruction Manual Download Page 4

Page: 4 / 36

D395-90-880 Issue E

Page ii

Edwards and the Edwards logo are trademarks of Edwards Limited.

Contents

Software upgrade .......................................................................................................18

5.5

Calibration service ......................................................................................................18

STORAGE AND DISPOSAL ....................................................................... 19

6.1

Storage ...................................................................................................................19

6.2

Disposal ................................................................................................................... 19

SPARES AND ACCESSORIES ..................................................................... 21

7.1

Introduction .............................................................................................................21

7.2

Accessories ...............................................................................................................21

Appendix A

Error Numbers ............................................................................ 23

Appendix B

RS232 Commands ........................................................................ 25

Appendix C

RS232 Queries ............................................................................ 27

Index .............................................................................................. 29

For return of equipment, complete the HS Forms at the end of this manual.

Illustrations

Figure

Page

Pin connections for an 8-way FCC/RJ45 ............................................................................. 4

Pin connections and pin-out for the analogue / relay connector ................................................ 5

Pin connections for the serial comms connector ................................................................... 6

Bench mounted dimensions (mm) ..................................................................................... 7

Panel cut-out required .................................................................................................. 8

Panel mounting the ADC ................................................................................................ 8

Rear panel connections ................................................................................................. 9

IBM PC RS232 interface - 9-way ......................................................................................10

IBM PC RS232 interface - 25-way .....................................................................................10

Front panel displays ....................................................................................................11

Summary of Contents for D395-90-000































Search results

Summary of Contents for D395-90-000

Reviews:

Related manuals for D395-90-000

Brands by name

Popular brands

Edwards D395-90-000, Instruction Manual

Search results

Summary of Contents for D395-90-000

Reviews:

Related manuals for D395-90-000

Brands by name

Popular brands