manualshive.com logo in svg

Edwards D395-90-000, Instruction Manual

Share
Download
Edwards D395-90-000 Instruction Manual Download Page 35

Index

D395-90-880 Issue E 

© Edwards Limited 2010. All rights reserved. 

Page 29

Edwards and the Edwards logo are trademarks of Edwards Limited.

A
Accessories ............................................... 21
Active gauge connectors ..................................4
ADC error numbers  ...................................... 23
Analogue / relay connector (enhanced only) ..........5
Appendix A ................................................ 23
Appendix B ................................................ 25
Appendix C ................................................ 27
B
Bench mounted dimensions (mm) .......................7
Bench-top mounting .......................................7
C
Calibration service  ...................................... 18
Checklist of components  .................................7
Cleaning the controller  ................................. 18
Commands ................................................ 15
Compatible gauges for the ADC  .........................1
Component checklist  ......................................7
Connecting active gauges  ................................9
Connecting the analogue / relay connector 
(enhanced only) .......................................... 10
Connecting the electrical supply  ........................9
Connecting the serial interface (enhanced only)  ... 10
Connections .................................................4
D
Dimensions of a bench mounted TIC (mm)  ............7
Display .......................................................3
Disposal ................................................... 19
E
Electrical data  .............................................3
Error Numbers ............................................ 23
F
Fault finding guide  ...................................... 17
Fitting the controller ......................................7
Front panel description  ................................. 11
Front panel display  ...................................... 11
Front panel symbols and their functions  ............. 11
Fuse ..........................................................3
G
Gauge ........................................................4
Gauge calibration ........................................ 14
Gauge connector pin-out  .................................4
Gauge display (standard)  ............................... 12
Gauge ID numbers  ....................................... 12
Gauge identification  .................................... 12
Gauge pressure display  ................................. 13
I
IBM PC RS232 interface - 9-way  ....................... 10
Installation ..................................................7
Introduction ........................................... 1, 21
L
Linking two ADCs (enhanced only)  .................... 16
M
Maintenance .............................................. 17
Mechanical data ............................................3
Menu items  ............................................... 13
Menu structure (enhanced)  ............................ 13
Message basics  ........................................... 15

O
Operating and storage data .............................. 3
Operation ..................................................11
P
Panel cut-out required  ..................................8
Panel mounting  ...........................................8
Panel mounting the ADC .................................8
Pin connections and pin-out for the analogue / 
relay connector  ...........................................5
Pin connections for an 8-way FCC/RJ45  ..............4
Pin connections for the serial comms connector  ....6
Power up ................................................. 11
Product description  ......................................1
Pump set up  ............................................. 14
Q
Queries ................................................... 15
R
Rear panel connections ..................................9
Rear panel description ...................................9
Responses ................................................ 16
RS232 commands  ...................................15, 25
RS232 operation (Enhanced only)  .................... 15
RS232 queries  .......................................16, 27
S
Safety .................................................... 17
Scope and definitions  ....................................1
Serial communications (enhanced only)  ..............6
Set-point 2 controlling gauge ......................... 14
Set-point adjustment  .................................. 13
Set-point an link threshold adjustment  ............. 13
Software upgrade ....................................... 18
Spares and accessories  ................................ 21
Storage ................................................... 19
Storage and disposal  ................................... 19
T
Technical data  ............................................3
U
Units selection  .......................................... 14
Unpack and inspect  ......................................7
Using analogue outputs  ................................ 10
Using relays .............................................. 10
Using two ADCs  ......................................... 16

Index

Summary of Contents for D395-90-000





































Reviews:

No comments

Brands by name

Popular brands

Load more brands