manualshive.com logo in svg

Edwards D395-90-000, Instruction Manual

Share
Download
Edwards D395-90-000 Instruction Manual Download Page 18

D395-90-880 Issue E

Page 12

© Edwards Limited 2010. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

OPERATION

4.3

Gauge identification

When a gauge is connected to the ADC, the display mode will change to display the reading from that gauge. An 
identification message consisting of "ID" followed by a number will be displayed for 3 seconds to show that the ADC 
has identified the new gauge. The ID numbers and corresponding gauges are shown in 

Table 7

.

If a gauge cannot be identified or is of a type which is not supported by the Controller, then the message "???" will be 
displayed.

Where an ASG is used, you need to select the full-scale range of the gauge. This can only be done when the gauge is 
first connected. After the identification message "ID15", the display will show 1.0

3

, representing a 1000 mbar ASG. 

You can change this to 2.0

3

 for a 2000 mbar ASG using the UP and DOWN keys (  /  ). When the required value is 

showing on the display, press the ENTER key ( 

 ).

4.4

Gauge display (standard)

The ADC will continuously display the pressure measured by an Active Gauge. The display is in exponential format. 
The pressure units are shown by the LEDs on the right of the display. Use the DOWN key (   ) to change the pressure 
units. The units mbar, Torr and Pascal will be selected in turn. A further press of the DOWN key (   ) will select 
voltage mode, in which the output voltage of the Active Gauge will be displayed, and the LED enunciators will 
extinguish. To return to pressure display, press the DOWN key (   ) again.

If an error condition is detected by the gauge or by the controller, then the display will show an error message of the 
form "Err" followed by a number. Refer to 

Appendix A

 for a list of error numbers and suggested remedies. To clear 

the error message from the display press the DOWN key (   ). If the error originated in a gauge it may be necessary 
to disconnect the gauge and correct the fault before the error message can be cleared.

If a gauge is not connected then the display will show "- - -".

Table 7 - Gauge ID numbers

ID number

Gauge

ID 04

APG-M / APG-MP

ID 05

APG-L

ID 06

APGX-H

ID 11

AIM-S

ID 15

ASG

ID 19

AIM-X

ID 20

WRG

ID 21

APGX-L / APGX-M / APGX-MP / 
APG100-XM / APG100-XLC

Summary of Contents for D395-90-000





































Reviews:

No comments

Brands by name

Popular brands

Load more brands