EDWARDS SYSTEMS TECHNOLOGY EST2, Installation Sheets Manual

Page: 120 / 120

P/N: 387204 REV: 2.0 Page 2 of 2
S9
S10
S10
S9
SWU-8(/3)
Group number Output addresses S1 dip switch settings Module
1 2 3 4
1 01-08 on off off off 2-SANCOM
2 09-16 off on off off SHO-4
3 17-24 on on off off SLU-16
4 25-32 off off on off SLU-16
5 33-40 on off on off SWU-8(/3)
6 41-48 off on on off SWU-8(/3)
7 49-56 on on on off
8 57-64 off off off on
9 65-72 on off off on
10 73-80 off on off on
11 81-88 on on off on
12 89-96 off off on on
Group number Input addresses S1 dip switch settings Module
1 2 3 4
1 01-08 on off off off 2-SANCOM
2 09-16 off on off off SHO-4
3 17-24 on on off off SWU-8(/3)
4 25-32 off off on off SWU-8/3
5 33-40 on off on off
6 41-48 off on on off
7 49-56 on on on off
8 57-64 off off off on
9 65-72 on off off on
10 73-80 off on off on
11 81-88 on on off on
12 89-96 off off on on
ON
ON
1
1
2
2
3
3
4
4
To set the dip switches:
A. Configure the SAN-CPU in the system programming utility.
B. Note the SWU-8(/3) in the programming utility (09 to 81).
C. Set the dip switches on S9 and S10 to match the group numbers of the SWU-8’s start input and start output addresses.
start input and output addresses of the
Set the dip switches. 3
Remember that the SWU-8:
Cannot occupy the 2-SANCOM addresses (01 through 09).
Requires one input address group and two output address groups,
which consist of eight addresses each.
Remember that the SWU-8/3:
Cannot occupy the 2-SANCOM addresses (01 through 09).
Requires two input address groups and two output address groups,
which consist of eight addresses each.
INSTALLATION
In this example, the
start address is 17
and the dip switch is
set to a binary 3.
Note: The SWU-8
only requires
addresses 17 to 24.
In this example, the
start address is 33
and the dip switch is
set to a binary 5.
To label the SWU-8(/3):
A. Identify each LED/switch group on the SWU-8(/3) according to its programmed function.
B. Write the functions on the slip-in legend sheet next to the appropriate LED/switch group.
C. Insert the label under the SWU-8(/3) face plate.
4 Label the SWU-8(/3).
Slip-in label
Make the ribbon cable connections. 2
JP1 JB1
P1 P1 P1
P1
P2 P2 P2
P2
2-SANCOM
From P1
on the
SAN-CPU
SLU-16 SWU-8(/3) SHO-4
A. Plug the ribbon cable assembly (P/N 250080) from P1 of the SAN-CPU into P2 of the 2-SANCOM.
B. Plug the ribbon cable from P1 of the 2-SANCOM to P2 of the next SAN series module.
C. Plug the ribbon cable from P1 of each SAN module to P2 of the next SAN module until you reach the last one.
D. Install the continuity jumper on the last SAN module.
Note: If the SWU-8(/3) is the last module, install the continuity jumper on JP1.
Technical Manuals Online! - http://www.tech-man.com
firealarmresources.com