manualshive.com logo in svg

Edvotek EdvoCycler, Quick Manual

Share
Download
Edvotek EdvoCycler Quick Manual Download Page 5

EDVOTEK®  •  1.800.EDVOTEK (1.800.338.6835)  •  FAX:  (301) 340.0582

www.edvotek.com  •  [email protected]

5

MAIN MENU

> LOAD SAVED PROGRAM
   MODIFY SAVED PROGRAM
   CREATE NEW PROGRAM
   DELETE SAVED PROGRAM
   TEMP HOLD PARAMS

LOAD PROGRAM

> 

330 

336 341 669

   331 

337 

701 

000

   332 

952 

004 

000

   333 

961 

371 

111

   334 

962 

764 

000

PROGRAM 330 

TEMP    TIME

Init Denat
Denaturation  

94       0040

Annealing  

45       0045

Extension  

72       0045

Final Ext  

72       0300

Cycles 

 

  01       30

PROGRAM >000  TEMP    TIME
Init Denat  

00    0000

Denaturation  

00    0000

Annealing   

00    0000

Extension   

00    0000

Final Ext   

00    0000

Cycles 

 

     00    00  

TEMPERATURE HOLD MENU

   TEMP HOLD ON
> SET HOLD TEMP  

010

   RETURN

Quick Guide Screens

A

B

C

D

E

GETTING STARTED

Turn on the power switch (“|” mark is on, “O” mark is off).
Use the up or down button on the front panel to select the desired
function (the arrow to the left of the menu will allow you to choose
that selection).

The five options are as follows:

LOAD SAVED PROGRAM
MODIFY SAVED PROGRAM
CREATE NEW PROGRAM
DELETE SAVED PROGRAM
RUN PROGRAM

LOAD SAVED PROGRAM

Use this function if you are running
an EDVOTEK® kit.  The programs for
most EDVOTEK® PCR kits are pre-
loaded on the EdvoCycler™ and
ready-to-run.  Simply follow ED-
VOTEK instructions for preparing
DNA samples for PCR and place
tubes in the EdvoCycler™.  The
block holds only 0.2 ml PCR tubes -
if PCR sample is prepared in a
different tube, you must transfer
sample to a 0.2 ml thin-wall PCR
tube (supplied in all EDVOTEK®
PCR kits).

1.

Scroll to 

LOAD SAVED PROGRAM

 and press enter.

2.

Scroll up or down to the desired program and press enter. Check
with the kit instructions to make sure parameters match with
screen display.  If they do not, reference 

MODIFY SAVED PRO-

GRAM

  section and make the necessary changes to the existing

program.

continued

IMPORTANT

Always check the PCR cycling

parameters in the EDVOTEK®
manual that accompanies your

experiment.  Compare the

program to ensure that it

matches the pre-programmed

cycles.  If there has been a

change, it will be necessary to
modify the existing program to

match the new parameters.

Summary of Contents for EdvoCycler









Reviews:

No comments

Brands by name

Popular brands

Load more brands