manualshive.com logo in svg

EDMA 267455, Instruction And Security Manual

Share
Download
EDMA 267455 Instruction And Security Manual Download Page 8

INSTRUCTION AND 

SECURITY MANUAL

MAJ - 05/18

AUTOMATIC USE ASSISTED BY POWER DRILL

1

First of all, you must use the power drill support base for safety reason. Then, set up the EDMAPLAC

®

MEGA 

according to the selected setting configuration.

Insert the hex bit in the 

power drill chuck 

Adjust the power drill 

support base according to 

the power drill dimensions.

Insert the hex bit fixed to the power drill, in the hex hole located in the 

middle of the steering wheel. Turn the power drill to block it against the 

power drill support base. Set the power drill on “maximum torque - low 

speed”, rotating on clockwise direction.

Pull the power drill trigger to lift the board.

To lower the top rack, remove the power drill first, then push the main brake lever while lifting 

up the safety brake latch.

2

3

4

5

6

Ref. 267455

POWER DRILL MINI 14.4 VOLTS - 3 Ah

power drill

DIRECTION OF

ROTATION

MAXIMUM  TORQUE

LOW  SPEED

Summary of Contents for 267455













Reviews:

No comments

Brands by name

Popular brands

Load more brands