background image

Page 8

Solution-8 Installation Manual

ISSUE401.DOC

Electronics Design & Manufacturing

Features

The 

Solution-8

 security control panel is microprocessor controlled with the highest degree of integration

ever seen in security control systems to date. This not only means more features but greater reliability and
performance. The design of every feature has been accomplished with continual consideration being given to the
end user and the installer. The control console is straight forward and uncluttered, so as not to complicate its
operation or make  programming confusing in any way. Its stylish appearance allows it to easily blend in with
modern and contemporary surroundings.

The cabinet has been laid out to allow for easy conduit entry and has ample room for wiring and a 6.5aH battery.
A dynamic battery tester has been incorporated which performs continual testing and monitoring of the backup
battery's condition and will report any failure through the system console. A battery can no longer be left
accidentally unconnected because the system will detect this failure and report it accordingly.

The Day Alarm feature enables you to monitor the opening of a front door of a shop, or unauthorised access into
a particular area. The remote arming feature gives you the ability to arm your system from any telephone in the
world.

In situations where the main console is installed in a bedroom and the indicators become annoying at night, the
console extinguish mode will automatically turn off all the indicators after sixty seconds. The console indicators
will illuminate the next time a key is pressed or an alarm occurs.

Programming has been made child's play with the introduction of the unique Programming Key. This simple
device exclusive to E.D.M. will revolutionise programming. Labour costs and the possibility of programming
errors will be greatly reduced.

The fully programmable, no compromise output system with its timing and polarity functions has made
interfacing as simple as one, two, three. This allows for easy control of all external devices. The Integrated
Protection System [I.P.S.] has also been incorporated into this revolutionary security control system adding
greater reliability along with incredible tolerance to incorrect wiring or adverse situations. The 24 Hour zones
have been enhanced with the addition of a Fire sound available to the horn speakers. This feature can be of great
use when using smoke detectors so that a distinctly different alert tone is generated from a 24 Hour Fire zone to
that of a standard 24 Hour Burglary zone.

E.D.M. has injected twenty years of knowledge and expertise into the 

Solution-8

 security control system

making it the most flexible, tolerant and easy to operate unit available on the market today. E.D.M. proves again
that an Australian owned company backed by Australians is by far one of the most technically advanced security
manufacturers in the market place today and in the future.

Summary of Contents for Solution 8























































Reviews: