Edimax Wireless Multi-Homing Broadband Router User Manual Download Page 70

Page: 70 / 103

2.5.6 ALG Settings

You can select applications that need “Application Layer Gateway” to support.

Parameters

Default Description

Enable

You can select to enable “Application Layer
Gateway”, then the router will let that
application correctly pass though the NAT
gateway.

Click <

Apply>

at the bottom of the screen to save the above configurations. You can now

configure other advance sections or start using the router (with the advance settings in place)

2.5.7 Static Routing

This router provides Static Routing function when NAT is disabled. With Static Routing,
the router can forward packets according to your routing rules.
Note: The DMZ function of firewall will not work if static routing is enabled.

Summary of Contents for Wireless Multi-Homing Broadband Router








































































































Search results

Summary of Contents for Wireless Multi-Homing Broadband Router

Reviews:

Related manuals for Wireless Multi-Homing Broadband Router

Brands by name

Popular brands

Edimax Wireless Multi-Homing Broadband Router, User Manual

Search results

Summary of Contents for Wireless Multi-Homing Broadband Router

Reviews:

Related manuals for Wireless Multi-Homing Broadband Router

Brands by name

Popular brands