manualshive.com logo in svg

EdilKamin BLADE2 H 18 UP, Installation, Use And Maintenance Manual

Share
Download
EdilKamin BLADE2 H 18 UP Installation, Use And Maintenance Manual Download Page 56

56

IT

ALIANO

USER/INSTALLER

MESSAGE

PROBLEM

SOLUTION

A07

Shutdown due to exceeding 
maximum smoke temperature.

•  Check the type of pellet (contact the technician if in 

doubt)

•  contact the technician

A08

Switching OFF due to excessive 
overheating of the product

• see 

HO7

A09

Shutdown due to gearmotor 
breakage or seizure

•  Contact the technician

A10

Switching OFF due to circuit 
board overheating.

•  Contact the technician

A11

Switching OFF due to the inter-
vention of the safety pressure 
switch.

•  Ensure the stove and flue are clean 
•  Contact the technician

A12

Room temperature probe 
failure. 

•  Contact the technician

A13

Shutdown due to breakage of 
the reading water temperature 
probe of the boiler stove.

•  Contact the technician

A14

Shutdown due to breakage of 
the water temperature probe in 
the boiler

•  Contact the technician

A15

Shutdown due to exceeding 
maximum water temperature in 
the boiler stove

•  Contact the technician

A16

Shutdown due to breakage of 
the pressure switch for reading 
the water pressure of the boiler 
stove

•  Contact the technician

A17

Shutdown due to breakage of 
the external probe

•  Contact the technician

A18

Shutdown due to breakage of 
the water temperature probe in 
the inertial storage tank

•  Contact the technician

A20

Shutdown due to gearmotor 
breakage or seizure

•  Contact the technician

TROUBLESHOOTING

Summary of Contents for BLADE2 H 18 UP





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands