Edgetech 2000-CSS User Manual Download

Page: 38 / 101

3-4

3.0: SETUP AND ACTIVATION

2000-CSS COMBINED SONAR

0017423_REV_C

ETHERNET 2:

RJ-45 connector. Available 10/100/1000BaseT Ethernet
connection.

USB:

(5) USB connectors. Four USB 2.0 ports two on the back panel
and two on the front. One USB 3.0 port on the back panel

VAC INPUT:

CEE-type AC input connector. Connects to 90–260 VAC, 50/60 Hz
power.

In addition, COM5–COM8 serial ports are available for use as required, each with DB-9 male connectors.
These connectors are located on the back panel.

3.5.2

Topside Computer Controls and Indicators

The Topside Computer includes controls and indicators on the front and back panels, as shown in

and

, are the following:

POWER:

Rocker switch. Switches AC power to the Topside Computer. This
switch can be left in the on position at all times.

SYSTEM POWER (switch):

Push button toggle switch. Turns the Topside Computer on or off.

SYSTEM POWER (indicator):

Green indicator. Illuminated when the Topside Computer is on.

RESET:

Momentary push button switch. Resets the Topside Computer.

HDD:

Yellow indicator. Flashes when a hard drive on the Topside
Computer is being accessed.

Summary of Contents for 2000-CSS






































































































Search results

Summary of Contents for 2000-CSS

Reviews:

Related manuals for 2000-CSS

Brands by name

Popular brands

Edgetech 2000-CSS, User Manual

Search results

Summary of Contents for 2000-CSS

Reviews:

Related manuals for 2000-CSS

Brands by name

Popular brands