Quick Start Guide
–
3
–
Safety and Regulatory Information
FCC Class A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections -
Category 3 or better for 10 Mbps connections, Category 5 or better for
100 Mbps connections, Category 5, 5e, or 6 for 1000 Mbps
connections. For fiber optic connections, you may use 50/125 or 62.5/
125 micron multimode fiber or 9/125 micron single-mode fiber.
CE Mark
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment complies with the requirements of
the Council Directive 2014/30/EU on the Approximation of the laws of
the Member States relating to Electromagnetic Compatibility and 2014/
35/EU for electrical equipment used within certain voltage limits. For the
evaluation of the compliance with these Directives, the following
standards were applied:
RFI Emission:
Limit according to EN 55032:2012+AC:2013, Class A
Limit for harmonic current emission according to EN 61000-3-
2:2014, Class A
Limitation of voltage fluctuation and flicker in low-voltage supply
system according to EN 61000-3-3:2013
Immunity:
Product family standard according to EN 55024:2010
Electrostatic Discharge according to IEC 61000-4-2:2008
Radio-frequency electromagnetic field according to IEC 61000-4-
3:2010
Electrical fast transient/burst according to IEC 61000-4-4:2012
Surge immunity test according to IEC 61000-4-5:2014
Immunity to conducted disturbances, Induced by radio-frequency
fields: IEC 61000-4-6:2013
Power frequency magnetic field immunity test according to IEC
61000-4-8:2009
Voltage dips, short interruptions and voltage variations immunity test
according to IEC 61000-4-11:2004
LVD:
EN 62368-1:2014/A11: 2017
The Declaration of Conformity (DoC) can be obtained from www.edge-
core.com -> support -> download.
Japan - VCCI Class A
Laser Safety
Warning: Fiber Optic Port Safety:
Avertissment: Ports pour fibres optiques - sécurité sur le plan optique
:
Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit:
Battery Safety
Power Cord Safety
Please read the following safety information carefully before installing the
device:
Warning:
Installation and removal of the unit must be carried out by qualified
personnel only.
The unit must be connected to an earthed (grounded) outlet to
comply with international safety standards.
Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
The appliance coupler (the connector to the unit and not the wall
plug) must have a configuration for mating with an EN 60320/IEC
320 appliance inlet.
The socket outlet must be near to the unit and easily accessible. You
can only remove power from the unit by disconnecting the power
cord from the outlet.
This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which it is connected also operates under SELV
conditions.
When using a fiber optic port, never look at the
transmit laser while it is powered on. Also, never look
directly at the fiber TX port and fiber cable ends when
they are powered on.
Ne regardez jamais le laser tant qu'il est sous tension.
Ne regardez jamais directement le port TX
(Transmission) à fibres optiques et les embouts de
câbles à fibres optiques tant qu'ils sont sous tension.
Niemals ein Übertragungslaser betrachten, während
dieses eingeschaltet ist. Niemals direkt auf den Faser-
TX-Anschluß und auf die Faserkabelenden schauen,
während diese eingeschaltet sind.
Warning:
If your device uses a lithium battery, do not attempt
to replace the battery yourself. Return the device to the
manufacturer for battery replacement.
Avertissement:
Si votre appareil utilise une batterie au
lithium, n’essayez pas de remplacer la batterie vous-même.
Renvoyez l’appareil au fabricant pour le remplacement de la
batterie.
If the device contains lithium batteries that are encased in a
sealed chassis, do not attempt to open the sealed chassis under
any circumstances.
Si l’appareil contient des piles au lithium logées dans un
châssis scellé, n’essayez en aucun cas d’ouvrir le châssis scellé.
Risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Risque d’explosion si la batterie est remplacée par un type
incorrect. Éliminez les piles usagées conformément aux
instructions.
䚷䛣䛾⨨䛿䚸䜽䝷䝇㻭ᶵჾ䛷䛩䚹䛣䛾⨨䜢ఫᏯ⎔ቃ䛷⏝䛩䜛䛸㟁Ἴጉᐖ䜢ᘬ䛝
㉳䛣䛩䛣䛸䛜䛒䜚䜎䛩䚹䛣䛾ሙྜ䛻䛿⏝⪅䛜㐺ษ䛺ᑐ⟇䜢ㅮ䛪䜛䜘䛖せồ䛥䜜䜛
䛣䛸䛜䛒䜚䜎䛩䚹㻌
㼂㻯㻯㻵㻙㻭
CLASS I
LASER DEVICE
DISPOSITIF LASER
DE CLASSE I
LASERGER
DER KLASSE I
ÄT
