background image

Technical manual 

PACKSOLO

 

– V1.5 

p.5/24 

 

 

Information and recommendations 

 

 

Pursuant  to  European  directive  UTE  C00-200,  incorporating  directives  89/336  EEC  and 
92/31 EEC, PACKSOLO complies with the following standards: 

 

NF EN 50081-1 governing electromagnetic radiation, and 

 

NF EN 50082-1 governing electromagnetic susceptibility. 

 

 

Cabling  recommendations:

  the  cables  used  to  connect  readers,  the  network  and  other 

peripherals  must  be  installed  in  accordance  with  the  instructions  for  Level  2  (protected 
environment) of standard NF EN 61000-4-4. 

 

This product must be installed by an approved company.

 Incorrect installation and usage 

may  result  in electric  shock  or  fire.  Before  installing  the  product,  read  the  technical 
information and comply with the recommendations. 

 

Once the power is turned off, all the internal capacitors will discharge themselves to a 
safe level after 60 seconds under normal conditions. However, in the event of a power 
failure,  the  charge  may  be  maintained  for  much  longer  and  suitable  precautions 
should be taken before handling the product. 

 

Summary of Contents for PACK SOLO

























Reviews: