Edelbrock 3530 Owner'S Manual Download Page 20 | Manualshive

Page: 20 / 33

background image

20

Pro-Flo EFI Installation Instructions

©2005 Edelbrock Corporation
Rev. 2/05

Brochure #63-0273

Catalog #3530 & #3531

The IAC is attached to the main wiring harness.

The ignition amplifier is attached to the main harness with the connector at left side of lower diagram. The ignition amplifier should
be mounted on the firewall, or on the passenger fender well. The KEY ON (Start/Run power) wire (pink) should be connected to the
factory positive (+) coil wire. If you have a ballast resistor in your factory coil wiring, you should remove the ballast resistor and
connect the KEY ON wire to the wire coming into the positive (+) side of the ballast resistor.

REFER TO VEHICLE REPAIR MANUAL

FOR WIRING DIAGRAM, IF NECESSARY.

The coil is attached to the main harness. We strongly recommend using an E-Core type (non-ballast resistor) coil as shown below.
These are available through most performance ignition parts suppliers. The coil attaches via the connector shown below. If using a
standard style coil, cut the connector off and use ring type connectors.

TO MAIN HARNESS

TO COIL

TO IGN AMP

TO MAIN
HARNESS

ATTACHES TO OEM
START/RUN POWER
(OEM POSITIVE “+” COIL WIRE)

TO COIL

TO MAIN HARNESS

TACHOMETER LEAD

«
...
18
19
20
21
22
...
»

Summary of Contents for 3530


































Reviews:

No comments

Related manuals for 3530

Brand: FORM FIT Pages: 2

Brand: FormFit Pages: 2

Brand: AC Schnitzer Pages: 20

Brand: Acura Pages: 6

Brand: Pontiac Pages: 20

Brand: BMW Pages: 64

WG Grand Cherokee 2002

Brand: Jeep Pages: 74

Brand: AA Products Pages: 8

Brand: Metra Electronics Pages: 12

Brand: Whispbar Pages: 42

Brand: 3UVIEW Pages: 15

GRAND CHEROKEE 4xe 2023

Brand: Jeep Pages: 440

Brand: Volkswagen Pages: 4

Brand: Honeywell Pages: 2

Brand: Toyota Pages: 12

handsfree communication

Brand: Toyota Pages: 42

Brand: Toyota Pages: 19

Brand: Unitec Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands