manualshive.com logo in svg

ECS P4VXASD2+, User Manual, Page: 37 / 44

Share
Download
ECS P4VXASD2+ User Manual Download Page 37

 

Parallel Port Mode 

Use this item to set the parallel port mode. You can select SPP (Standard 
Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel 
Port), or ECP + EPP. 

Parallel Port IRQ 

Use this item to assign IRQ to the parallel port. 

Parallel Port DMA 

Use this item to assign a DMA channel to the parallel port. 

OnBoard Game Port 

This item enables or disables the I/O address for the game port. 

OnBoard MIDI Port 

Use this item to enable or disable the onboard MIDI port, and to assign a port 
address. 

MIDI Port IRQ 

Use this item to assign IRQ 7 to the parallel port. 

OnBoard IDE 

Use this item to enable or disable the onboard IDE channel. 

OnBoard AC’97 Audio 

This item enables or disables the AC’97 audio chip. 

OnBoard MC’97 Modem 

This item enables or disables the MC’97 modem chip. 

USB Controller 

Use this item to select the USB ports or disabled. 

USB Device Legacy Support 

This item allows you to enable the USB device, if you have installed a USB 
device on the system board. 

 

 

 

 

 

 

 

33 

Summary of Contents for P4VXASD2+













































Reviews:

No comments