manualshive.com logo in svg

ECS P4VXASD2+, User Manual, Page: 29 / 44

Share
Download
ECS P4VXASD2+ User Manual Download Page 29

 

Entering the Setup Utility 

When you power on the system, BIOS enters the Power-On Self Test (POST) 
routines. POST is a series of built-in diagnostics performed by the BIOS. After 
the POST routines are completed, the following message appears: 

Press DEL to enter SETUP 

Pressing the delete key 

 accesses the BIOS Setup Utility: 

AMIBIOS SIMPLE SETUP UTILITY – VERSION  1.21.05  

(C) 2000  American Megatrends, Inc. All Rights Reserved 

Standard CMOS Setup 
Advanced Setup 
Power Management Setup 
PCI / Plug and Play Setup 
Load Optimal Settings 
Load Best Performance Settings 

 Features 

Setup 

  CPU PnP Setup 
 Hardware 

Monitor 

 Change 

Password 

 Exit 

Esc :  Quit 

↑

  

↓

  

→

   

←

 :  Select Item 

F10  :  Save & Exit Setup 

Time, Date, Hard Disk Type . . . 

BIOS Navigation Keys 

The BIOS navigation keys are listed below: 

Key Function 

Esc 

Exits the current menu 

←↑↓→

 

Scrolls through the items on a menu 

+/–/PU/PD 

Modifies the selected field's values 

F10 

Saves the current configuration and exits setup 

F1 

Displays a screen that describes all key functions 

F5 

Loads previously saved values to CMOS 

F6 

Loads a minimum configuration for troubleshooting. 

F7 

Loads an optimum set of values for peak performance 

 

 

 

 

 

 

25 

Summary of Contents for P4VXASD2+













































Reviews:

No comments