manualshive.com logo in svg

ECS P4VXASD2+, User Manual, Page: 33 / 44

Share
Download
ECS P4VXASD2+ User Manual Download Page 33

 

Manual AGP Comp. Driving 

When AGP Driving is set to Manual, use this item to set the AGP current driv-
ing value. 

AGP Mode 

This item provides the OnBoard VGA mode with three options of 1,2,

 

4 multi-

plied frequency. 

AGP Aperture Size 

This item defines an AGP for the graphics. Leave this item at the default value 
64MB. 

Auto Detect DIMM/PCI Clock 

When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI 
slots. 

CLK Spread Spectrum 

Use this item to set the system bus spread spectrum for the installed proces-
sor. 

Power Management Setup Page 

This page sets some of the parameters for system power management opera-
tion. 

AMIBIOS SETUP – POWER MANAGEMENT SETUP  

(C) 2000 American Megatrends, Inc. All Rights Reserved 

 

ACPI Aware O/S 

 

Yes  

Power Management/APM  

Enabled 

Video Power Down Mode 

Suspend 

Hard Disk Power Down Mode 

Standby 

Standby Time Out (Minute) 

Disabled 

Suspend Time Out (Minute) 

Disabled 

PowerOn by LAN/Ring  

Disabled 

PowerOn by Onchip LAN 

Disabled 

PowerOn by KBC 

 

Disabled 

    Wake up key  

 

Any key 

          Wake up password 

N/A 

Power On RTC Alarm   

Disabled 

RTC Alarm Date 

 

15 

RTC Alarm Hour 

 

12 

RTC Alarm Minute 

 

30 

RTC Alarm Second 

 

30 

 

ESC  :  Quit             

↑↓←→

  :  Select Item 

F1     :  Help             PU/PD/+/-  :  Modify 
F5     :  Old Values   (Shift)F2    :  Color 
F6     :  Load BIOS Defaults 
F7     :  Load Setup Defaults 

ACPI Aware O/S

 

This item supports ACPI (Advanced Configuration and Power management 
Interface). Use this item to enable or disable the ACPI feature. 

Power Management 

Use this item to enable or disable a power management scheme. If you en-
able power management, you can use the items below to set the power 
management operation. Both APM and ACPI are supported. 

29 

Summary of Contents for P4VXASD2+













































Reviews:

No comments