background image

5

2 - SAFETY SYMBOLS AND WARNINGS

CAUTION

Indicates a hazardous situation which, if not 

avoided, could result in minor or moderate injury.

!

  

 WARNING

Indicates a hazardous situation which, if not 

avoided, could result in death or serious injury.

!

  

DANGER

Indicates a hazardous situation which, if not 

avoided, WILL result in death or serious injury.

!

  

This is the safety alert symbol.  Symbol alerts 

you to potential personal injury hazards. Obey all 

safety messages following this symbol to avoid 

possible injury or death.

Become familiar with symbols identifying potential hazards.

Boiler installation shall be completed by qualified agency.  

2.1. Safety Information

 WARNING

Do not tamper with or use this boiler for any 

purpose other than its intended use. Failure to follow 

these instructions could result in death or serious 

injury. Use only manufacturer recommended parts 

and accessories.

!

  

CAUTION

Laceration, burn hazard.  Metal edges and parts 

may have sharp edges and/or may be hot. Use 

appropriate personal protection equipment to 

include safety glasses and gloves when installing 

or servicing this boiler. Failure to follow these 

instructions could result in minor or moderate injury. 

!

!

  

NOTICE

Used to address practices not related to personal 

injury.

 WARNING

Fire, explosion, asphyxiation and electrical shock 

hazard.  Improper installation could result in death 

or serious injury.  Read this manual and understand 

all requirements before beginning installation.

!

  

FOR YOUR SAFETY READ BEFORE OPERATING

Hot Water Can Scald

!

Water heated to temperature for clothes washing, 

dish washing and other sanitizing needs can scald and 

cause permanent injury.

Children, elderly, and infirm or physically handicapped 

persons are more likely to be permanently injured by 

hot water. Never leave them unattended in bathtub or 

shower. Never allow small children to use a hot water 

tap or draw their own bath.

If anyone using hot water in the building fits the above 

description, or if state laws or local codes require 

certain water temperatures at hot water taps, you 

must take special precautions:

• Use lowest possible temperature setting.

• Install some type of tempering device, such as 

an automatic mixing valve, at hot water tap or 

water heater. Automatic mixing valve must be 

selected and installed according  to manufacturer's 

recommendations and instructions.

• Water passing out of drain valves may be 

extremely hot. To avoid injury:

•  Make sure all connections are tight.

• 

 Direct water flow away from any person.

   

DANGER

!

  

Water 

Temperature 

Setting

1st Degree Burn 

Exposure Time For 

An Adult

2nd and 3rd Degree Burn 

Exposure Time For An 

Adult

120°  F

1 minute

5 minutes

130°  F

5 seconds

30 seconds

140° F

2 seconds

5 seconds

150°  F

1 second

1.5 seconds

160°  F

Instantaneous

0.5 seconds

Note:

 Warning for Infants, Children, and Elderly: 

Great care must be taken when exposing the  

aforementioned groups to warm or hot water as they 

can be badly burned in exposure times less than half 

of the time for an adult.

PN 240013090 REV. C [10/01/2021]

Summary of Contents for Dunkirk WPSB 3 Series





































Reviews: