background image

8

3.3  Boiler Location Considerations

• Ambient room temperature always above 32°F (0°C) to 

prevent the potential of freezing. 

• Drainage of water (or water/ antifreeze solution) during 

boiler service or from safety relief valve discharge.

• Access to system water piping, gas supply, and 

electrical service. 

• 

Boiler shall be installed on flat level surface which is 

capable of supporting the weight of the boiler, water, 

and equipment. 

• 

Raise boiler above the floor on blocks if floor may get 

wet.

3 - LOCATING THE BOILER

Items to Avoid

Products Which May Contain These 

Items

Areas Where These Items May Be 

Found

Chlorine, Fluorine, and Compounds

Spray cans containing chlorofluorocarbons

Chlorinated waxes/cleaners
Chlorine-based swimming pool chemicals
Calcium chloride used for thawing
Sodium chloride used for water softening
Swimming pool  or spa chemicals
De-icing salts or chemicals
Carbon Tetrachloride

Swimming pools and pool storage areas

Laundry room (Note 2)
Confined storage areas

Airborne Particulates

Drywall dust
Road or gravel dust
Dryer lint
Cat litter

Construction or remodelling areas (Note 1)

Laundry room (Note 2)

Acids, Solvents, etc.

Paint, Varnish, Turpentine, etc.
Cleaning Solvents
Hydrochloric acid/muriatic acid
Cements, adhesives and glues

Photo processing plants
Garages with workshops

Furniture refinishing areas and 

establishments

Laundry Chemicals

Laundry detergents, bleaches, fabric 

softeners, etc.
Antistatic fabric softeners (dryer sheets)

Dry cleaning/laundry areas and 

establishments

Other

Permanent wave solutions
Refrigerants (Freon, etc) (only where 

the refrigerant may be leaking from the 

appliance)

Beauty shops
Refrigeration repair shops

Notes:  

1. It is recommended the boiler be isolated and not operated during construction/

renovation.  Excessive particles ingested by the boiler may accumulate in the flueway 

passages possibly resulting in unsafe operation.  In this case, unit servicing shall include 

cleaning of flueway passages and burner ports.
2. If locating boiler in laundry room is unavoidable, it is manufacturer recommended 

the room be generously ventilated (well in excess of combustible air requirements), and 

homeowner seal laundry supply containers, and minimize room vapors.

3

. Piping allowing fresh air in should also be considered.  See Section 5-1.

Table 3-1: CONTAMINANTS

• Horizontal run to chimney shall be as short as possible.
• System piping exposed to freezing conditions: Use 

inhibited propylene glycol solutions certified by fluid 

manufacturer for use with closed water heating system.  

Do not use automotive or ethylene glycol.

PN 240013090 REV. C [10/01/2021]

Summary of Contents for Dunkirk WPSB 3 Series





































Reviews: