background image

16 

BUTTONS AND FUNCTIONS 

Works both if the sensor is covered or not for children and elderly usage, also 

works when child seat is used. 

Press once to start child cleansing, regular cleansing  time is 90 seconds  and  warm 

air-drying  is  240  seconds.  Press  again  to  activate  pulsate  cleansing,  again  to  stop 

pulsate cleansing. 

Child function: by default, water temperature: level 3,  nozzle location: level 5, water 

pressure: level 2, dryer temperature: level 2. 

Note: when child function is on, all the function will be disabled until child cleansing is 

finished. (Except child clean button and stop button). 

Works when user is sitting on the unit and seat sensor is covered. 

Press once to start rear cleansing, regular cleansing time is 90 seconds and warm air-

drying is 240 seconds, press again within 90 seconds to activate pulsate cleansing, 

again to stop pulsate cleansing. 

After adjusting user preferences, press and hold setting button for 4 seconds, when 

top  light  indicator  and  the  fifth  function  light  indicator  starts  to  flash,  rear  cleansing 

preference has been set. 

Works when user is sitting on the unit and seat sensor is covered. 

Press  once  to  initiate  warm  air  drying,  regular  drying  time  is  240  seconds, 

corresponding light indicator will display current temperature setting. Press wind temp 

button to switch between temperature settings. 

Works when user is sitting on the unit and seat sensor is covered. 

Press once to start front cleansing, regular cleansing  time is 90 seconds and warm 

air-drying is 240 seconds, press again within 90 seconds to activate pulsate cleansing, 

again to stop pulsate cleansing. 

After adjusting user preferences, press and hold setting button for 4 seconds, when 

top light indicator and the fifth function light indicator starts to flash, female cleansing 

preference has been set. 

Press once to start user setting function which regular cleansing time is 90 seconds 

and  warm  air-drying  is  240  seconds.  (Water  temperature,  nozzle  position,  water 

pressure and dryer temperature will process by user’s setting). press again within 90 

seconds to activate pulsate cleansing, again to stop pulsate cleansing.

 

Press  BACK  button  and  FRONT  button  to  control  nozzle  position.  1  light  indicates 

minimum nozzle position, and 5 lights indicate maximum nozzle position. 

When in auto-setting mode, press BACK button to turn OFF and FRONT button to turn 

ON selected function. 

Press once to stop function which is running and switch to standby mode. Press and 

hold button for 4 seconds, all the light indicators will light up for 3 seconds then all the 

function will be reset. 

Press once to turn on hot and cold massage function. Press again to turn it off. 

Hot and cold massage function: the massage which water temperature will alternate 

between high and low in one cleansing cycle. 

Press to switch between water pressure settings. 

○○○○○: 0 light on

- no water pressure activates.

●●●●●: 5 lights on

- 0.9 L/min or 0.24 gal/min

Child Mode

Rear Wash

Air Dry

Front Wash

User Setting

Back/Off

Front/On

Stop

Hot/Cold massage

Water Pressure

Summary of Contents for TitanDT300 2050






















Reviews: