background image

4

SETTINGS AND ADJUSTMENTS

The Gemini can be turned on or off, and adjusted, using 

either the included remote or the control panel on the front 

of the unit. Both the remote and the control panel buttons 

have the same functions.

Fan Speed

Power  

ON/OFF

Ions

Display Screen

Timer

Power ON/OFF

ActivePure

Timer

Fan Speed

Ions

Auto Mode

POWER (stand by)

 

Turns the unit ON and OFF. 

FAN SPEED 

Controls the fan speed and 

auto function setting. The 

color around the power 

button changes depending on 

fan speed: 

  • Quiet

 is green. 

  • Low

 is blue. 

  • Medium

 is orange. 

  • High

 is red.

AUTO MODE

This mode automatically sets 

the unit according to the 

air quality detected by the 

dust and gas/odor sensor. 
Ionization generator and 
ActivePure work together 

when the unit is in Auto 

Mode.

IONS

Indicates that ionization is 
working. The Ion button turns 
the ionizer on and off.

ACTIVEPURE

Indicates the photocatalytic 

purification is operating. The 

ActivePure mode starts and 

stops the ActivePure function. 

 UV LAMPS  

UV1 or UV2 will illuminate 

when the relative UV tube fails 

to work or needs replacing. 

The Display Screen is used to display all current settings (see 
page 4) as well as any maintenance reminders.

DISPLAY SCREEN 

Ions

Check Filter

ActivePure

TIMER

Indicates the automatic shut 

off is on. The timer count (1-12 
hours) is set with the Timer 

button. 

 

 CHECK FILTER 

Check Filter illuminates after 
an accumulative 3,000 hours 

of usage as a reminder to 

change the prefilter and 

activated carbon filter. The 

HEPA filter should also be 
checked against the color 

shades located on the frame 

to determine if replacement 

is needed. 

  DUST AND GAS  

Indicates the level of current 

air quality detected. The chart 

below shows the five quality 

levels that are displayed.

In Auto Mode, the unit 

automatically adjusts the 

fan speed to compensate for 

contaminant levels.

PLEASE NOTE 

- if there is no 

wavy line shown, dust and gas 

are below detectable levels.

Very 

Good

Good

Ordinary Poor

Dust Indicator

Timer

Fan Speed Settings

Gas Indicator

UV Replacement  
Indicator

Excellent

Summary of Contents for Gemini









Reviews: