background image

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

© 2015 Ecolink Intelligent Technology Inc. 

 

 

 

 

 

 

 

 

 

 

 

 

 

PN PIR-ZWAVE2  R1.04 

 

 

 

Configuration Set Values

 

Effect

 

Parameter Number: 1          Size: 1

 

Configuration Value: 0x00

 

(Default) Sensor does NOT send Basic Sets to Node IDs in Association Group 2 when the sensor is restored (i.e. Motion 

Not Detected ).

 

Parameter Number: 1          Size: 1

 

Configuration Value: 0xFF

 

Sensor sends Basic Sets of 0x00 to nodes in Association Group2 when sensor is restored.

 

Parameter Number: 2          Size: 1

 

Configuration Value: 0x00

 

(Default) Sensor sends Sensor Binary Reports when sensor is faulted and restored for backwards compatibility in 

addition to Notification Reports.

 

Parameter Number: 2          Size: 1

 

Configuration Value: 0xFF

 

Sensor will send only Notification Reports and NOT Sensor Binary Reports when the sensor is faulted and restored.

 

  

FCC Compliance Statement

 

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference 

in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

 

Re-orient or relocate the receiving antenna 

 

Increase the separation between the equipment and receiver 

 

Connect the equipment to an outlet on a different circuit from the receiver 

 

Consult the dealer or an experienced radio/TV contractor for help. 

 

Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc. could void the user’s authority to operate the equipment. 

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, 
including interference that may cause undesired operation of the device. 

C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et (2) c’et appareil 
doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de la dispositif. 

FCC ID:   XQC-PIRZ1      IC:   9863B-PIRZ1 Warranty 

Ecolink Intelligent Technology Inc. warrants that for a period of 3 years from the date of purchase that this product is free from defects in material and workmanship. This warranty does not apply to damage caused by 
shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or as a result of any unauthorized modifications. 

If there is a defect in materials and workmanship under normal use within the warranty period Ecolink Intelligent Technology Inc. shall, at its option, repair or replace the defective equipment upon return of the equipment 
to the original point of purchase. 

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink Intelligent 

Technology Inc. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this 
product.  The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for any warranty issue shall be limited to a replacement of the defective product. It is recommended that the customer check 
their equipment on a regular basis for proper operation. 

Summary of Contents for PIR-ZWAVE2











Reviews: