background image

 BEFORE PERFORMING ANY 
 ELECTRICAL WORK, READ THESE 
 WARNINGS

1. All wiring must comply with local and national 

    electrical codes, regulations and must be installed

    by a licensed electrician.

2. All electrical connections must be made according 

    to the Electrical Connection Diagram located on 

    the panels of the indoor and outdoor units. 

3. If there is a serious safety issue with the power 

    supply, stop work immediately. Explain your

    reasoning to the client, and refuse to install the 

    unit until the safety issue is properly resolved.

4. Power voltage should be within 90-110% of rated 

    voltage. Insufficient power supply can cause 

    malfunction, electrical shock, or fire. 

5. Power must be connected to fixed wiring, a

    surge protector and main power switch

    should be installed. 

6. If connecting power to fixed wiring, a service 

    disconnect that disconnects all poles and 

    has a contact separation of at least 1/8in (3mm) 

    must be incorporated in the fixed wiring. The 

    qualified technician must use an approved 

    circuit breaker or switch.    

7. Only connect the unit to an individual branch 

    circuit outlet. Do not connect another 

    appliance to that circuit.   

8. Make sure to properly ground the air conditioner.

9. Every wire must be firmly connected. Loose 

    wiring can cause the terminal to overheat, 

    resulting in product malfunction and possible fire.

    Do not let wires touch or rest against refrigerant 

    tubing, the compressor, or any moving parts 

    within the unit.  

    To avoid getting an electric shock, never touch 

    the electrical components soon after the power

    supply has been turned off. After turning off 

    the power, always wait 10 minutes or more 

    before you touch the electrical components.

10. 

11. 

13. 

Make sure that you do not cross your

       electrical wiring with your signal wiring.

       This may cause distortion and interference.

14. 

Connect the outdoor wires before connecting 

       the indoor wires.

Wiring

 WARNING

BEFORE PERFORMING ANY 
ELECTRICAL OR WIRING WORK, 
TURN OFF THE MAIN POWER TO 
THE SYSTEM. 

 

 

 

 

Summary of Contents for MOX330-18HFN1-MR0































Reviews: