ECM NH3 5250 Instruction Manual Download Page 8

 

Safety Warnings 

 
In  installation  and  use  of  this  product,  comply  with  the  National  Electrical  Code  and  any 

other applicable Federal, State, or local safety codes. 
 

The NH

3

 sensor is heated, gets hot, and can burn you. 

 
Always wear eye protection when working near engines, vehicles, or machinery. 
 

During  installation,  turn  off  the  power  and  take  all  other  necessary  precautions  to  prevent 

injury,  property  loss,  and  equipment  damage.    Do  not  apply  power  until  all  wiring  is 

completed. 
 

Never work on a running engine. 
 

When installing the NH

3

 5250s cabling and sensor(s) on a stopped engine, it is best to think-

out your moves before you make them. 
 

Route and cable-tie all cables away from hot, moving, sharp, or high voltage (spark) objects. 
 

Take  into  consideration  the  movement  of  the  engine,  chassis,  and  wind  buffeting  when 

instrumenting the engine. 
 

Clear tools away from the engine before starting. 
 

Operate  the  engine  only  in  a  well  ventilated  area  and  never  when  you  or  one  of  your  co-

workers is tired. 
 

When operating the NH

3

 5250 in a moving vehicle, the operator should keep his or her eyes 

on the road. 
 
One  measure  of  professionalism  is  how  much  you  and  your  co-workers  can  accomplish 
without an injury.  Always be at your professional best.  Think and act with safety in mind. 

Summary of Contents for NH3 5250































































Reviews: