Eclipse RatioMatic 500 System Manual Download | Manualshive

Page: 38 / 460

background image

Section 2. Avio Avionics Suite

Eclipse 5OO Systems Manual

Copyright

© — Eclipse Aviation Corporation

18

Version 2.0 April 2007

Engine System Control- Ignition control Engine dry motoring

Fire Suppression

Fuel system control- electric fuel pumps, fuel crossfeed

Flight Controls- primary flap and trim control, secondary trim control

Electrical- control of electronic circuit breakers

Environmental- fan activation and speed, temperature control

Pressurization- aircraft pressurization settings

Ice Protection- anti-ice and de-ice controls

Primary landing gear control

Exterior Lighting- command of ECB’s to activate and deactivate lighting

2.2.3 Systems Monitoring and reporting

The systems monitoring and reporting capability of the ACS’ allow reporting of
various systems status to the pilot through the Primary and Multi-Function Displays
(PFD & MFD). Examples of system monitoring and fault sensing include:

Electrical system monitoring

Fuel System monitoring- (fuel gauging probes, fuel pumps, valves)

Secondary engine parameter monitoring- (fuel flow, oil temperature, oil pressure)

Engine fire detection

Pressurization and climate control system monitoring (temperature sensors,
valves)

Trim monitoring- (trim motor the current state and position of primary and
secondary flight controls: flaps, trims, control surfaces)

Landing gear monitoring- (gear position, actuator operation)

Ice Protection monitoring- (operation of anti-ice and deice system components)

Door indication monitoring- (state of main cabin door)

Brake system monitoring- (brake fluid level)

Oxygen system monitioring- (oxygen pressure)

Control monitoring is often attached to various Crew Alerting System Messages
(CAS), (ex. PARKING BRAKE status message indicates that the PARKING BRAKE
handle is pulled out).

As a compliment to monitoring of systems, the ACS also provides fault sensing
capability for the various systems components and their associated sensors. Failure
monitoring is provided for various systems, some examples include the failure of:
flap actuators; control valves, such as the fuel shutoff valve; sensors, such as the
climate control temperature sensors. Should a component or sensor fail a CAS
message is displayed to the pilot to indicate that a failure has occurred. Due to the
built in redundancy of aircraft systems, many of these failures do not result in a
complete loss in system functionality, but only a loss in a redundant component.

«
...
36
37
38
39
40
...
»

Summary of Contents for RatioMatic 500













































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RatioMatic 500

Brand: Roban Pages: 47

Brand: High Adventure Pages: 22

Brand: Air Design Pages: 35

Brand: Air Design Pages: 38

Glasflugel 304S

Brand: HPH Pages: 63

Brand: Best Pages: 16

Brand: Ozone Pages: 36

Brand: ICARO paragliders Pages: 26

Brand: Saab Pages: 670

Brand: Triple Seven Pages: 16

Brand: Glider.it Pages: 32

Brand: Dudek Pages: 28

Brand: Dudek Pages: 32

Brand: Dudek Pages: 48

Brand: Kanardia Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands