manualshive.com logo in svg

Eclipse RatioMatic 500, System Manual

Share
Download
Eclipse RatioMatic 500 System Manual Download Page 306

Section 13.  Air Data 

 

Eclipse 5OO  Systems Manual 

 Copyright

 

© — Eclipse Aviation Corporation  

286

 

 Version 2.0   April 2007  

13.7 Abnormal Procedures 

13.7.1  Air Data Disagreement 

If abnormal indications are generated by the ADC (i.e. airspeed, altitude, attitude, 
heading, and temperature) the incorrect source is flagged to the pilot via one of 
several DISAGREE caution and advisory messages and requires  

DISAGREE CAS MESSAGES: 

„

 

ADC 

⎯

 

AIRSPEED DISAGREE (Caution) 

⎯

 

ALTITUDE DISAGREE (Caution) 

„

 

AHRS 

⎯

 

ATTITUDE DISAGREE (Caution) 

⎯

 

HEADING DISAGREE (Caution) 

„

 

Temperature 

⎯

 

TAT DISAGREE (Advisory) 

These messages require pilot action to compare air data in question with the other 
source(s) of information.  Once a valid source is determined, the pilot selects the new 
source via the SENSOR page on the MFD.  A TAT DISAGREE advisory message 
requires that the pilot view the ICE protection synoptic to compare temperature 
indications. 

13.7.2  Sensor Failure 

The air data system is a redundant design, preventing complete loss of air data in the 
event of a component failure.  Should any component, ADC, AHRS, or GPS fail, one 
of the following messages will appear: 

„

 

AHRS 1 FAIL (CAUTION) 

„

 

AHRS 2 FAIL (CAUTION) 

„

 

ADC 1 FAIL (ADVISORY) 

„

 

ADC 2 FAIL (ADVISORY) 

„

 

ADC 3 FAIL (ADVISORY) 

„

 

GPS 1 FAIL (ADVISORY) 

„

 

GPS 2 FAIL (ADVISORY) 

With ADC and AHRS SRC on the SENSOR page selected to AUTO, the ACS will 
automatically revert to using the operating source for air data information.  Since all 
air data information is sent through the on-side AHRS to the ACS, should an AHRS 
fail with AUTO selected, the affected PFD will use the AHRS and ADC from the 
opposite side.  Example: AHRS 1 fails; the Left PFD will use AHRS 2 and ADC 2.   

 CAUTION: 

A failure of ADC 1, 2 or AHRS 1, 2 will reduce functionality such that flight in 
RVSM airspace may NOT be continued. The autopilot will also disengage and 
NOT be able to be reengaged.  

There is no pilot control over GPS selection. In the event of a GPS failure, the ACS 
will automatically revert to the operating GPS.   

Summary of Contents for RatioMatic 500













































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands