5. set the front stop trigger screw as required, ensuring
that the bar is as close to 0% as possible when the
trigger is fully released against the set screw. it is
advisable to allow for some extra travel in the trigger
release once the bar has reached its minimum value.
6. Adjust the
rEl pT
parameter so that when the trigger
is fully released the bar settles beneath the indicator on
the left hand side of the screen (see page 49)
.
7. set the magnet return strength screw and the
spring return strength screw as required, making both
the spring tension and the return force as strong as
possible without compromising the “feel” of the trigger.
TraiNiN
ThE TraiNiNg paraMETEr
the
TraiNiN
parameter is used to select training mode.
in training mode the Geo will function exactly the same
as normal but with two important differences:-
1. the solenoid valve is under - driven so that the bolt
only moves a small amount and does not release a
burst of air. this simulates the firing cycle without
wasting air and generating lots of noise.
2. the bbss is overridden so that the Geo can cycle
without paint. the centre of the bbss indicator changes
to a ‘t’ to indicate that training mode is enabled.
the training parameter choices are as follows:-
> OFF:
training mode is disabled and the Geo functions
normally.
> ON:
training mode is enabled.
> caNcEl:
cancel editing and leave the parameter
unchanged.
rEl pT
ThE rElEasE pOiNT paraMETEr
the
rEl pT
parameter is only available if
OpTO
has been
selected in the hardware menu.
rEl pT
defines the
point at which the trigger is considered released and is
adjustable between 1% and 49% in 1% increments.
Basic TriggEr
FilTEr sET-Up
the majority of trigger bounce problems can be
eliminated by utilizing one of the nine fixed
dBOUNcE
choices (level 1-9). in attempting to eliminate trigger
bounce it is advisable to try the nine fixed
dBOUNcE
choices before attempting any advanced set up of the
trigger filters.
adVaNcEd TriggEr
FilTEr sET-Up
in order to optimize the trigger filters it is necessary to
have the
pUll pT
parameter set as high as possible and
the
rEl pT
parameter set as low as possible:
1. select the
pUll pT
parameter. observe that the
graphical bar rises and falls as the trigger is pulled
and released. the actual value of the graphical bar is
displayed in the top right of the display.
2. set the rear stop trigger screw as required, ensuring
that the bar is as close to 100% as possible when the
trigger is fully depressed against the set screw. it is
advisable to allow for some extra travel in the trigger
pull once the bar has reached its maximum value.
3. Adjust the
pUll pT
parameter so that when the
trigger is fully depressed the bar settles above the
indicator on the left hand side of the screen (see page
49).
4. select the
rEl pT
parameter. observe that the
graphical bar rises and falls as the trigger is pulled
and released. the actual value of the graphical bar is
displayed in the top right of the display.
note: the fAstest wAy to shoot A Geo is to wAlk the
triGGer with two or more finGers. feAtherinG (not
fully releAsinG) the triGGer will cAuse the filterinG
system to reduce the rAte of fire in order to
eliminAte whAt it perceives to be triGGer bounce.
AD
VA
N
CE
D
S
ET
-U
P
50.
CONTENTS
ORIENTATION
QUICK SET-UP
USING YOUR GEO
ADVANCED SET-UP
MENU TREE
MAINTENANCE
FAULT FINDING
SERVICE CENTERS
PARTS LIST
SPARES & ACCESSORIES
51.
AD
VA
N
CE
D
S
ET
-U
P
ADVANCED SET-UP
QUicK gUidE
Summary of Contents for GEO
Page 1: ......
