Echotrek SE-300 Series Installation And Programming Manual Download Page 7

Page: 7 / 52

SE/SG-300 series two-wire compact ultrasonic level transmitters

TECHNICAL DATA

General data

Transducer materials

Polypropylene (PP)
Kynar (PVDF)
Teflon (PTFE)
Stainless Steel (DIN 1.4571, AISI SS316Ti)

Housing material

Plastic: PBT fibre-glass reinforced, flame-retardant (DuPont



)

Aluminium: Powder paint coated

Process temperature

PP, PTFE and PVDF versions: -30 °C ... +90 °C
Stainless Steel versions : -30°… +100°C (120° for max. 2 hours)

Ambient temperature

-30°C ... +60°C with SAP-200 –25 °C ... +60 °C

Pressure (Absolute)

0.5** ... 3 bar (0.05 ... 0.3 MPa) Stainless steel versions 0.9 ... 1.1 bar (0.09 ... 0.11 MPa)

Seals

PP transducer: EPDM

All other transducer versions: FPM (Viton)

Ingress protection

Sensor: IP68

Housing: IP67 (NEMA 6)

Power supply /
Consumption

11.4 ... 36 VDC 48 mW ... 720 mW galvanic isolation; protection against surge transients

Accuracy *

(0.2% of the measured distance plus 0.05% of the range)

Resolution

Depending on the measured distance < 2 m: 1 mm, 2...5 m: 2 mm, 5...10 m: 5 mm, > 10 m: 10 mm
Analogue: 4 … 20 mA, R

max

600 Ohm, isolated, secondary lightning protection

Loop power test connectors: 2 mm socket for ampermeter, 200 mV, 0.5%
Display: 6 digits, icons and bargraph, (on SAP-200 display module only)

Outputs

Serial communication: HART interface (close end resistor 250 Ohm)

Electrical connection

2 x Pg16 and 2 x ½” NPT for cable protection pipe
Cable diameter: 10 … 14 mm ; Wire cross section: 0.5 ... 1.5 mm

Electrical protection

Class I with aluminium housing, Class II with plastic housing

Under optimal conditions of reflection and stabilised transducer temperature.

At pressures under 1 bar absolute, please consult your distributor

Summary of Contents for SE-300 Series





















































Search results

Summary of Contents for SE-300 Series

Reviews:

Related manuals for SE-300 Series

Brands by name

Popular brands

Echotrek SE-300 Series, Installation And Programming Manual

Search results

Summary of Contents for SE-300 Series

Reviews:

Related manuals for SE-300 Series

Brands by name

Popular brands