background image

Page 20 

Radio Interference

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

1. this device may not cause harmful interference, and 

2. this device must accept any interference received, including interference that may cause undesired 

operation.

Modifying this receiver may void your authority to use the equipment. This equipment has been tested and 
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. If this equipment 
does cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

If none of the remedies on the previous page stops the radio interference, you should contact a licensed 
radio/television technician, your satellite dealer, or call the Customer Service Center at 1-800-333-3474, 
for assistance. 

Summary of Contents for DISH Pro Plus Twin LNBF


























Reviews: