Echo SRM-251SB Operator'S Manual Download Page 28

Page: 28 / 32

* Install and use U-Handle when operating any model with blade.

MODEL ----------------------------------------------------- SRM-251SB

Shaft Length ------------------------------------------------ 1828 mm (72.0 in.)

Unit Width -------------------------------------------------- 313 mm (12.31 in.)

Unit Height ------------------------------------------------- 235 mm (9.25 in.)

Weight (dry) w/cutting attachment ---------------------- 5.64 kg (12.43 lb.)

Engine Type ------------------------------------------------ Air cooled, two-stroke, single cylinder gasoline engine

Bore ---------------------------------------------------------- 34.0 mm (1.34 in.)

Stroke -------------------------------------------------------- 28.0 mm (1.10 in.)

Displacement ----------------------------------------------- 25.4 cc (1.55 cu. in.)

Exhaust System -------------------------------------------- Spark Arrestor Muffler w/catalyst

Carburetor -------------------------------------------------- Zama w/purge

Ignition System -------------------------------------------- CDI (capacitor discharge ignition)

Spark Plug -------------------------------------------------- NGK BPM-8Y Gap 0.65 mm (0.026 in.)

Fuel ---------------------------------------------------------- Mixed (Gasoline and Two-stroke Oil)

Fuel/Oil Ratio ----------------------------------------------- 50:1 ECHO High Performance, two-stroke air cooled engine oil

Gasoline ----------------------------------------------------- 89 Octane unleaded. DO NOT use fuel containing methyl alcohol,

more than 10% ethyl alcohol or 15% MTBE.

Oil ------------------------------------------------------------ 50:1 ECHO High Performance, two-stroke air cooled engine oil

Fuel Tank Capacity ---------------------------------------- 0.42 lit. (14.2 US fl. oz.)

Starter System ---------------------------------------------- Automatic Recoil Starter

Clutch ------------------------------------------------------- Centrifugal Type

Drive Shaft (upper & Lower) ----------------------------- 6.35 mm (1/4 inch) Flex Shaft

Rotating Direction ----------------------------------------- Counter clockwise viewed from top

Cutting Attachment --------------------------------------- Nylon line head (2-line) with .095 in. Cross Fire

line capacity

6 m (20 ft.)

Handles* ---------------------------------------------------- Front - Loop, Rear - Grip, when operating with standard line head

Shoulder Harness ------------------------------------------ Optional

Idle Speed (RPM) ------------------------------------------ 2,500 - 3,000

Wide Open Throttle Speed (W.O.T.)

with Nylon Line Head ------------------------------------- 8,500 - 10,500 RPM

Wide Open Throttle Speed (W.O.T.)

with Blade --------------------------------------------------- 10,000 - 12,000 RPM

PECIFICATIONS

Summary of Contents for SRM-251SB

































Search results

Summary of Contents for SRM-251SB

Reviews:

Related manuals for SRM-251SB

Brands by name

Popular brands

Echo SRM-251SB, Operator'S Manual

Search results

Summary of Contents for SRM-251SB

Reviews:

Related manuals for SRM-251SB

Brands by name

Popular brands