Echo SRM-251SB Operator'S Manual Download Page 10 | Manualshive

Page: 10 / 32

background image

10

C

PLASTIC

SHIELD

INSTALLATION

(for Nylon Line Operation)

Tools Required: Screwdriver.

Parts Required: Plastic Shield, Shield Plate, three (3) 5mm x 16mm

screws.

NOTE
The plastic shield is for use with the Nylon Line Head only.
Install Metal Shield when using plastic or metal blades.

4. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft

hole. Insure locator pin is fully engaged by twisting lower drive
shaft. Locator pin should snap flush in coupler. Full engagement will
prevent further shaft rotation.

5. Secure lower shaft assembly to coupler by tightening clamping

knob (D).

1. Remove plastic sleeve and upper plate (A) from PTO shaft.

2. Install the shield on the bottom of the bearing housing flange.

3. Place shield plate (B) on shield, align holes and install three (3)

5x16 mm screws.

4. Install upper plate (A).

B

A

NYLON

LINE

HEAD

INSTALLATION

Tools Required: Head Locking Tool,

Parts Required: Nylon Line Head.

1. Be sure upper adaptor plate remains on PTO shaft.

2. Align locking hole in upper plate with notch in edge of gear housing

and insert head locking tool (C).

3. Thread line head onto shaft by turning it counter clockwise until

head is tight against upper plate.

4. Remove head locking tool.

C

«
...
8
9
10
11
12
...
»

Summary of Contents for SRM-251SB

































Reviews:

No comments

Related manuals for SRM-251SB

Brand: Makita Pages: 2

Brand: Makita Pages: 49

Brand: Makita Pages: 13

Brand: Echo Pages: 8

Brand: Shindaiwa Pages: 16

Brand: LawnMaster Pages: 28

N1F-GT-250/18-D

Brand: ALDI Pages: 37

Brand: Makita Pages: 48

Brand: Black & Decker Pages: 16

Brand: Black & Decker Pages: 4

Brand: Qualcast Pages: 16

Brand: McCulloch Pages: 1

Brand: McCulloch Pages: 21

Brand: Jonsered Pages: 36

Brand: Jonsered Pages: 65

Brand: Alpina Pages: 84

Brand: Hoftronic Pages: 7

Brand: 909 Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands