Echo SRM-22GES Operator'S Manual Download Page 3

Page: 3 / 24

SRM-22GES

DECALS AND SYMBOLS

Carefully read the operator’s
manual

Wear eyes, ears and head
protection

Carburettor adjustment
- Low speed mixture

Purge bulb (Primer)

Petrol and oil mixture

Warning, side thrust

The maximum speed of the
cutting attachment shaft in r/min

Carburettor adjustment
- High speed mixture

Symbol form/shape

Symbol description/application

Symbol form/shape

Symbol description/application

Emergency stop

Keep bystanders away 15 m

Usage without shield not
permitted

Carburettor adjustment
- Idle speed

Warning!
Thrown objects!

Wear foot protection and gloves

Locate this safety decal on your unit. The complete unit
illustration found in the “DESCRIPTION” section will help
you locate them.

Part Number 890617-43130

Make sure the decal is legible and that you understand and
follow the instructions on it. If a decal cannot be read, a new
one can be ordered from your ECHO dealer.

Usage of metal blades not
permitted

DANGER

This symbol accompanied by the word

“DANGER”

calls attentions to an act or a condition which will lead
to serious personal injury or death of operators and
bystanders.

WARNING

This symbol accompanied by the word

“WARNING”

calls attentions to an act or a condition which can
lead to serious personal injury or death of operators
and bystanders.

CAUTION

“CAUTION”

indicates a potentially hazardous

situation which, if not avoided, may result in minor or
moderate injury.

Circle and slash symbol means whatever
is shown is prohibited.

NOTE

This enclosed message provides tips for use, care
and maintenance of the unit.

Summary of Contents for SRM-22GES

























Search results

Summary of Contents for SRM-22GES

Reviews:

Related manuals for SRM-22GES

Brands by name

Popular brands

Echo SRM-22GES, Operator'S Manual

Search results

Summary of Contents for SRM-22GES

Reviews:

Related manuals for SRM-22GES

Brands by name

Popular brands