manualshive.com logo in svg

Echo SRM-22GES, Operator'S Manual

Share
Download
Echo SRM-22GES Operator'S Manual Download Page 16

16

SRM-22GES

  WARNING

• WHEN ENGINE STARTS, THE CUTTING

ATTACHMENT MAY ROTATE, EVEN WITH
THROTTLE TRIGGER IN LOW-SPEED POSI-
TION.

• WHEN ENGINE IS STARTED, CONFIRM IF

THERE IS NOT ANY ABNORMAL VIBRATION
OR  SOUND. IF THERE IS ABNORMAL
VIBRATION OR SOUND, ASK YOUR DEALER
TO REPAIR.

OPERATION

Ignition switch

START

STARTING COLD ENGINE

Feature of this model: “ES” START
“ES” START

 generates enough revolving power to rotate

crankshaft up to a speed to ignite the engine and bring
almost no kickback.

“ES” START

 makes engine start far easier than you ever

expect.

• Before starting engine make sure cutting attachment is

not in touch with ground or other objects.

• Place ignition switch in “START” position.
• Push purge bulb until fuel is visible in clear fuel return

line.

• Move choke lever to CLOSE position.
• Pull starter handle until first firing sound.
• Open choke.
• Restart engine and allow to warm up.

STARTING WARM ENGINE

• Place ignition switch in “START” position.
• Move choke lever to OPEN position.
• If tank is not empty, pull starter handle.
• If fuel tank is empty, after refilling, push the purge bulb

(until fuel is visible in clear fuel return line). Pull starter
handle.

Choke lever

CLOSE

NOTE

If engine does not start after 4 pulls, use Cold
Starting Procedure.

STOPPING ENGINE

• Release throttle trigger and allow engine to idle.
• Place ignition switch in “STOP” position.

Throttle trigger
lockout

Throttle trigger

Spark plug wire

Spark plug

Always disconnect the spark plug wire from the spark plug
to ensure the engine cannot be started before you work on
the unit or leave it unattended.

  WARNING

IF ENGINE DOES NOT STOP, CLOSE CHOKE TO
STALL ENGINE. HAVE YOUR ECHO DEALER
INSPECT AND REPAIR IGNITION SWITCH
BEFORE USING THE UNIT.

NOTE

• Check unit for loose nuts, bolts and screws before

starting.

• Always clear work area of debris before starting

operation.

• Always hold the unit firmly on the ground.
• When pulling starter handle, use short pulls, 1/2 to

2/3 of rope length.

• Do not allow the starter handle to snap back

against the housing.

Starter handle

Fuel return line

Ignition switch

Throttle trigger lockout

Throttle trigger

OPEN

Purge bulb

Summary of Contents for SRM-22GES

























Reviews:

No comments

Brands by name

Popular brands

Load more brands