manualshive.com logo in svg

Echo SRM-22GES, Operator'S Manual

Share
Download
Echo SRM-22GES Operator'S Manual Download Page 18

18

SRM-22GES

COOLING SYSTEM MAINTENANCE

IMPORTANT

To maintain proper engine operating temperature,
cooling air must pass freely through the cylinder
fin area. This flow of air carries combustion heat
away from the engine.

Overheating and engine seizure can occur when:

• Air intakes are blocked, preventing cooling air

from reaching the cylinder,

or

• Dust and grass build up on the out side of the

cylinder. This build-up insulates the engine and
prevents the heat from leaving.

Removal of cooling passage blockages or
cleaning of cylinder fins is considered “Normal
Maintenance”. Any resultant failure attributed to
lack of maintenance is not warranted.

• Remove dust and dirt from between fins.

• Before each use, remove accumulated debris from bottom

engine intake grille located between the fuel tank and
starter.

CHECK SPARK PLUG

• Check plug gap. Correct gap is 0.6 to 0.7 mm.

• Inspect electrode for wear.

• Inspect insulator for oil or other deposits.

• Replace plug if needed and tighten to 15 - 17 N•m (150

to 170 kgf•cm).

0.6 to 0.7 mm

CLEANING SILENCER

• Clean deposits from silencer and tighten two bolts.

Two bolts

Silencer cover

Silencer

ANGLE TRANSMISSION

• Remove plug from angle transmission.

• Add grease, if necessary, using low pressure pump.

• Reinstall plug.

NOTE

Use good quality lithium multi grease. DO NOT
overfill housing.

Angle transmission

Plug (Bolt)

Grease tube

Air intake

Cylinder fins

Hexagonal
wrench

Summary of Contents for SRM-22GES

























Reviews:

No comments

Brands by name

Popular brands

Load more brands