manualshive.com logo in svg

Echo SRM-225, Operator'S Manual, Page: 30 / 52

Share
Download
Echo SRM-225 Operator'S Manual Download Page 30

MAINTENANCE

SRM-225

30

X7722279402

© 2/2016 ECHO Inc.

Air Filter

Level 1.

1.

Close choke (COLD START [

] position). This prevents dirt from 

entering the carburetor throat when the air filter is removed. Brush 
accumulated dirt from air cleaner area.

2.

Remove air filter cover. Brush dirt from 
inside cover.

3.

Replace filter if it is damaged, fuel soaked, 
very dirty, or the rubber sealing edges are 
deformed.

• Lightly brush debris from filter.

• Soak heavily soiled filters in water/

detergent solution to loosen dirt, then 
brush lightly. 

• Rinse with clean water and allow to dry 

completely before reuse. 

4.

Install air filter in air filter case. 

5.

Install air filter cover.

Fuel Filter

Level 1.

Fuel is VERY flammable. Use extreme care when mixing, storing or 
handling, or serious personal injury may result.

1.

Use a clean rag to remove 
loose dirt from around fuel cap 
and empty fuel tank.

2.

Pull the fuel filter from the fuel 
tank.

3.

Remove the filter from the line 
and install the new filter.

Parts Required:

REPOWER

TM

 AIR & FUEL FILTER KIT.

Parts Required:

REPOWER

TM

 AIR & FUEL FILTER KIT.

Summary of Contents for SRM-225





















































Reviews:

No comments