Echo SRM-225 Operator'S Manual Download Page 20 | Manualshive

Page: 20 / 52

Echo SRM-225 Operator'S Manual Download Page 20

OPERATION

SRM-225

20

X7722279402

© 2/2016 ECHO Inc.

Remove Nylon Line Head

Note: Do not disassemble nylon

line head.

1.

Align locking hole in upper plate
with notch in edge of gear
housing and insert head locking
tool (D).

2.

Remove line head (E) by turning
it clockwise until head is
completely off of shaft.

3.

Remove locking tool (D).

Support Handle
Installation

Note: Label shows

minimum spacing
for support handle
location.

1.

If necessary, position
support handle for
comfortable operation
and securely tighten
screws.

OPERATION

Moving parts can amputate fingers or cause severe injuries. Keep
hands, clothing and loose objects away from all openings. Always
stop engine, disconnect spark plug, and make sure all moving
parts have come to a complete stop before removing obstructions,
clearing debris, or servicing unit.

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a
poison gas. Breathing CO can cause unconsciousness, serious
injury, or death. Exhaust can cause serious burns. ALWAYS
position unit so that exhaust is directed away from your face and
body.

D

E

MIN

SPACING

«
...
18
19
20
21
22
...
»

Summary of Contents for SRM-225





















































Reviews:

No comments