Echo SHC-225/S Operator'S Manual Download Page 31 | Manualshive

Page: 31 / 44

background image

X7502257007

31

© 4/2016 ECHO Inc.

SHC-225/S

MAINTENANCE

Gear Case

Level 1.

1.

Clean dirt from the grease fitting
(A).

2.

Carefully pump grease into fitting
(A). DO NOT force grease. Too
much pressure will force grease
past seals and cause damage.
Apply 1 - 2 pumps of grease every
15 - 25 hours of operation.

3.

Wipe excess grease from around
grease fitting.

Drive Shaft Assembly

Level 1.

Hedge Trimmer blades are very sharp. Touching them may lead to
severe personal injury. Avoid touching blades whenever possible,
and always wear gloves to protect hands.

1.

Remove gear housing locating
screw (A) and loosen clamping
screw (B). Remove the gear
housing assembly from the drive
shaft housing.

Parts Required:

Lithium Based Grease.

Parts Required:

Lithium Based Grease.

A

A

B

D

«
...
29
30
31
32
33
...
»

Summary of Contents for SHC-225/S













































Reviews:

No comments

Related manuals for SHC-225/S

Brand: Pope Pages: 12

Brand: Lightronics Pages: 6

Brand: Ozito Pages: 8

Brand: FLORABEST Pages: 68

Brand: Troy-Bilt Pages: 24

Brand: Swisher Pages: 24

Brand: Brother Pages: 236

Brand: Rebel TOOLS Pages: 125

Brand: GreenWorks Tools Pages: 137

Brand: GreenWorks Pages: 14

Brand: GreenWorks Pages: 23

Brand: GreenWorks Pages: 132

Brand: GreenWorks Pages: 132

Brand: Chauvet Pages: 11

Brand: AL-KO Pages: 260

Brand: AL-KO Pages: 172

Brand: AL-KO Pages: 266

Decora Multi-Remote MSE0R-1

Brand: Leviton Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands