Echo SHC-225/S Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 44

background image

OPERATION

SHC-225/S

18

X7502257007

© 4/2016 ECHO Inc.

◆

Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.

◆

NEVER refuel a unit when the engine is HOT or RUNNING!

◆

DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.

◆

DO NOT overfill fuel tank. Wipe up spills immediately.

◆

Securely tighten fuel tank cap and close fuel container after
refueling.

◆

Inspect for fuel leakage. If fuel leakage is found, do not start or
operate unit until leakage is repaired.

◆

Move at least 3 m (10 ft.) from refueling location before
starting the engine.

Mixing Instructions

1.

Fill an approved fuel container
with half of the required amount of
gasoline.

2.

Add the proper amount of 2-stroke
oil to gasoline.

3.

Close container and shake to mix
oil with gasoline.

4.

Add remaining gasoline, close fuel
container, and remix.

Spilled fuel is a leading cause of hydrocarbon emissions. Some states
may require the use of automatic fuel shut-off containers to reduce fuel
spillage.

After use

• DO NOT store a unit with fuel in its tank. Leaks can occur.

Return unused fuel to an approved fuel storage container.

Storage

- Fuel storage laws vary by locality. Contact your

local government for the laws affecting your area. As a
precaution, store fuel in an approved, airtight container.
Store in a well-ventilated, unoccupied building, away from sparks and flames.

Stored fuel ages. Do not mix more fuel than you expect to use in thirty
(30) days, ninety (90) days when a fuel stabilizer is added.

Fuel to Oil Mix – 50:1 Ratio

US

Metric

Gas

Oil

Gas

Oil

Gallons

Oz.

Liter

CC.

1

2.6

5

100

2

5.2

10

200

5

13

25

500

«
...
16
17
18
19
20
...
»

Summary of Contents for SHC-225/S













































Reviews:

No comments

Related manuals for SHC-225/S

Brand: Parkside Pages: 216

Brand: Niko Pages: 16

Brand: Shindaiwa Pages: 12

Brand: Nakayama Pages: 29

Brand: AEG Pages: 16

Craftsman 536.796526

Brand: Sears Pages: 16

Brand: Challenge Xtreme Pages: 2

Brand: Challenge Xtreme Pages: 18

Brand: Rupes Pages: 28

790 AST Prime & Pull

Brand: MTD Pages: 24

Brand: Haussmann Pages: 24

Brand: Philio Technology Corporation Pages: 6

Brand: Peach Pages: 28

YARD MACHINES 599

Brand: MTD Pages: 54

Brand: MTD Pages: 60

Brand: Yard Machines Pages: 56

Brand: Yaros Pages: 112

Brand: Yard force Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands