background image

20

WARNING          DANGER

Inspect starting area for hazards such as rocks, glass, debris etc.
which could be contacted by the cutting attachment when starting.
Keep helpers and bystanders at least 15 M (50 ft.) from starting
area, otherwise serious personal injury may result.

4.

Lay the pruner on a flat clear area. Firmly grasp rear handle and
throttle trigger lockout with left hand and fully depress throttle
trigger to wide open position. Rapidly pull recoil starter handle (D)
until engine fires (or maximum five [5] pulls).

5.

After engine fires (or five [5] pulls), move choke to “Run” position.
Hold throttle trigger and throttle trigger lockout fully depressed
and pull recoil starter handle/rope until engine starts and runs.
Release throttle trigger and allow unit to warm up at idle for several
minutes.

NOTE
If engine does not start with choke in “Run” position after 4 pulls,
repeat instructions.

6.

After engine warm up, gradually depress throttle trigger to increase
engine RPM to operating speed.

STARTING

 

WARM

 

ENGINE

WARNING             DANGER

The cutting attachment should not rotate at idle. If cutting attach-
ment rotates, readjust carburetor according to "Carburetor Adjust-
ment" instructions in this manual or see your dealer, otherwise
serious personal injury may result.

1.

Stop Switch - Start/Run.  Move stop switch button (A) forward
away from the STOP position.

2.

Recoil Start - Pull Rope.  Lay the trimmer on a flat clear area and
pull the recoil starter handle (C) until the engine fires.

    NOTE
    If engine does not start after 4 pulls, use Cold Start Procedure.

B

C

A

Summary of Contents for PPFD-2400 TYPE 1/1E



































Reviews: