background image

10

CONTENTS

__ 1, Drive Shaft / Edger Assembly
__ 1, Power Head
__ 1, Plastic Bag (Co-Pack)
__ 1, Operator's Manual
__ 1, Safety Manual
__ 1, Warranty Registration Card
__ 1, ECHO Emissions and Warranty Statement
__ 1, 50:1 1 Gal. ECHO Oil Mix
__ 1, Front Handle
__ 4, 5X35 mm screws
__ 4, 5 mm nuts
__ 1, Scrench (Combination Spark Plug Socket/Screwdriver
__ 1, split pin
__ 1, 4 mm Hexagon Wrench
__ 1, Locking Tool
__ Safety Glasses

D

ESCRIPTION

The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions,
shield installation and other assembly may be necessary.

After opening the carton, check for damage.  Immediately notify your retailer or ECHO Dealer of damaged or missing
parts.  Use the contents list to check for missing parts.

EMISSION

 

CONTROL

The emission control system for this engine is EM (Engine Modification).

An Emission Control Label is located on the engine.  (This is an EXAMPLE ONLY, information on label varies by engine
FAMILY).

I

MPORTANT  ENGINE  INFORMATION

ENGINE FAMILY: VEH025UB24RA
DISPLACEMENT: 25.4cc
THIS ENGINE MEETS U.S. EPA PHI AND 1995 -
1999 CALIFORNIA EMISSION REGULATIONS FOR
ULGE ENGINES. REFER TO OWNER’S MANUAL
FOR MAINTENANCE SPECIFICATIONS AND
ADJUSTMENTS.

Summary of Contents for PE-2601





























Reviews: