background image

8

1.

AIR CLEANER - 

Contains replaceable air filter element.

2.

SPARK PLUG -

 Provides spark to ignite fuel mixture.

3.

SPARK ARRESTOR - CATALYTIC MUFFLER / MUFFLER -

 The muffler or catalytic muffler controls exhaust

noise and emission. The spark arrestor screen prevents hot, glowing particles of carbon from leaving the muffler.

Keep exhaust area clear of flammable debris.

4.

RECOIL STARTER HANDLE

 - Pull recoil handle slowly until starter engages, then quickly and firmly.  When

engine starts, return handle slowly.  DO NOT let handle snap back or damage to unit will occur.

5.

CHOKE  -

 Choke is located on the side of the air cleaner. Move choke lever to "COLD START" (

) to close choke

for cold starting. Move choke lever to "RUN" (

) position to open choke.

6.

PURGE BULB

 - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from the

carburetor.  Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line.  Pump purge bulb
an additional 4 or 5 times.

7.

FUEL TANK CAP -

 Covers and seals fuel tank.

8.

THROTTLE POSITION LEVER/STOP SWITCH  - 

Combination stop switch and variable speed throttle lever.

When the lever is moved all the way forward the blower is at Wide Open Throttle (W.O.T.). When the lever is

moved rearward to detent, the blower is at idle. When the lever is moved rearward past the idle detent the blower will

stop.

9.

BLOWER PIPES - 

Exclusive positive locking system.

10.

SAFETY DECAL - 

Lists important safety precautions.

11.

THROTTLE HANDLE -

 Rotates downward for throttle control access. Spring loaded for flexible operation.

12.

SHOULDER HARNESS - 

Used to support unit on operator's back. The straps are adjustable.

13.

FLEXIBLE PIPE - 

Allows for full range of movement.

14.

STICK HANDLE 

- Provides comfortable grip for directing air flow.

C

ONTENTS

1 - Power Head
1 - Flex Pipe
1 - Pipe w/swivel
1 - Straight Pipe
1 - Straight Pipe
1 - Operator's Manual
1 - Warranty Registration Card
1 - ECHO Emissions and Warranty Statement
1 - Plastic Bag

2 - Clamps w/screws
1 - Stick Handle
1 - Bolt 6x45
1 - Washer 6
1 - Wing nut

1 - Bottle Echo Power BlendX 

TM

 Universal 2-Stroke Oil

Summary of Contents for PB-610





























Reviews: