background image

21

P

ower

 B

lower

o

Perator

'

s

 M

anual

spark

 

plug

Level 1.

   

 

 

Parts Required:

    Repower

TM  

Tune Up Kit

IMPORTANT

Use only NGK BPM8Y spark plug (BPMR8Y in Canada) other-

wise severe engine damage may occur.

 

1.  Remove spark plug , and check for fouling, worn and rounded 

center electrode.

 2.  Clean the plug or replace with a new one.  DO NOT sand blast to 

clean. Remaining sand will damage engine.

 3.  Adjust spark plug gap by bending outer electrode.

 4.  Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).

CoolIng

 

sysTem

Level 2.

Parts Required:

   None, if you are careful.

 

IMPORTANT  

 To maintain proper engine operating temperatures, cooling air must

pass freely through the cylinder fin area. This flow of air carries

combustion heat away from the engine.

Overheating and engine seizure can occur when:

•  Air intakes are blocked, preventing cooling air from reaching the  

cylinder.

•  Dust and grass build up on the outside of the cylinder. This build up  

insulates the engine and prevents the heat from leaving.

Removal of cooling passage blockages or cleaning of cooling fins is 

considered “Normal Maintenance”.  Any failure attributed to lack of 

maintenance is not warranted.

Cleaning Grill

 1.  Remove accumulated debris from intake grill between backpack 

frame and blower housing.

0.65 mm

(0.026 in.)

Summary of Contents for PB-500H

































Reviews: