Echo PB-2620 Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 52

background image

OPERATION

PB-2620

18

X7501190602

© 10/2017 ECHO Inc.

Operation of this equipment may create sparks that can start
fires around dry vegetation. This unit is equipped with a spark
arrestor to prevent discharge of hot particles from the engine.
Contact local fire authorities for laws or regulations regarding
fire prevention requirements.

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a
poison gas. Breathing CO can cause unconsciousness, serious
injury, or death. Exhaust can cause serious burns. ALWAYS
position unit so that exhaust is directed away from your face
and body.

◆

This blower should be used for clearing leaves, grass,
debris, and dust in yards, gardens, driveways, and parking
lots only.

◆

Always maintain a direct, clear line of site to the unit and
the work being performed.

◆

Always be alert for changes in operation of unit.

◆

Always shut engine off before transporting unit to new
location.

◆

Always secure the unit during transportation to prevent
turnover, fuel spillage, and damage to the unit.

Fuel

Diesel fuels and alternative fuels, such as E-15 (15% ethanol),
E -85 (85% ethanol) or any fuels not meeting ECHO
requirements are NOT approved for use in ECHO 2-stroke
gasoline engines. Use of diesel or alternative fuels may cause
performance problems, loss of power, overheating, fuel vapor
lock, and unintended machine operation, including, but not
limited to, improper clutch engagement. Diesel or alternative
fuels may also cause premature deterioration of fuel lines,
gaskets, carburetors and other engine components.

«
...
16
17
18
19
20
...
»

Summary of Contents for PB-2620





















































Reviews:

No comments

Related manuals for PB-2620

Brand: Stiga Pages: 29

Brand: ebm-papst Pages: 11

Brand: Lavorwash Pages: 96

(-)(-)80MSX050A30SA

Brand: Rheem Pages: 52

Brand: Ryobi Pages: 12

Brand: Cub Cadet Pages: 48

Brand: Craftsman Pages: 22

Brand: Craftsman Pages: 14

Brand: Craftsman Pages: 32

Brand: Craftsman Pages: 22

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 28

Brand: Craftsman Pages: 23

Brand: Craftsman Pages: 12

Brand: Craftsman Pages: 11

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 20

Brand: Craftsman Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands