background image

 

H

edge

 C

lipper

 

 

O

peratOr

'

s

 M

anual

 

27

s

torage

  

 WARNING

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear 

of flammable debris during transportation or when storing, otherwise serious personal injury may result.

Long Term Storage (over 30 days)

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte-

nance which includes the following:
1.  Store unit in a dry, dust free place, out of the reach of children.

  

  WARNING

Hedge Clipper blades are very sharp.  Touching them may lead to severe personal injury.  Avoid touching blades 

whenever possible, and always wear gloves to protect hands. 

  

 DANGER

Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark, otherwise serious 

personal injury may result.

2.  Place the stop switch in the “OFF” position.

3.  Remove accumulation of grease, oil, dirt and debris 

from exterior of unit.

4.  Perform all periodic lubrication and services that are 

required.

5.  Apply clean oil to the entire length of the blade.  Be 

certain the blade bolts are lubricated.

6.  Install blade cover on blades.

7.  Tighten all the screws and nuts.

8. 

Drain

 the fuel tank 

completely

 and pull the recoil 

starter handle several times to remove fuel from the 

carburetor.

9.  Remove the spark plug and pour 7cc (1/4 oz.) of fresh, 

clean, two-stroke engine oil into the cylinder through 

the spark plug hole.

  A. Place a clean cloth over the spark plug hole.

  B. Pull the recoil starter handle 2-3 times to distribute  

  the oil inside the engine.

  C. Observe the piston location through the spark    

  plug hole.  Pull the recoil handle slowly until the  

  piston reaches the top of its travel and leave it    

  there.

10. Install the spark plug (do not connect ignition cable).

IMPORTANT

Always store and transport hedge clippers in a stable, horizontal position. Support gear case and cutting blades to 

prevent excessive flexing, which may cause damage to these components. Always install blade cover when transport

-

ing or storing unit. 

Summary of Contents for HC-150 - 11-09 1

































Reviews: