background image

8

X7702094204

© 04/2013 ECHO Inc.

EMISSION CONTROL (EXHAUST & EVAPORATIVE)

GT-230

Avoid Hot Surfaces

• Keep exhaust area clear of flammable debris. Avoid contact 

during and immediately after operation.

Equipment

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved 
attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, 
attachments or accessories which have not been tested and approved by ECHO. Read and comply 
with all safety instructions listed in this manual and safety manual.

• Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed.

• Inspect shield for damage and ensure that the cut-off knife is securely in place. Replace if either is 

damaged or missing.

• Check that the cutting attachment is firmly attached and in safe operating condition.

• Check that handle and harness (if included) are adjusted for safe, comfortable operation. See Assembly 

Section for proper adjustment.

Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects 
away from all openings.

ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete 
stop before removing obstructions, clearing debris, or servicing unit.

DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.

NEVER reach into any opening while the engine is running. Moving parts may not be visible through 
openings.

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or 
leaks are found, do not use unit, otherwise serious personal injury or property damage may occur. 
Have unit repaired by an authorized servicing dealer before using.

EMISSION CONTROL (EXHAUST & EVAPORATIVE)

EPA 2010 and Later and/or C.A.R.B. TIER III

The emission control system for the engine is EM (engine modification) 
and, if the second to last character of the Engine Family on the Emission 
Control Information label (sample below) is “C”, “K”, or “T”, the emission 
control system is EM and TWC (3-way catalyst). The fuel tank/fuel line 
emission control system is EVAP (evaporative emissions). Evaporative 
emissions for California models are only applicable to fuel tanks.

Summary of Contents for GT-230

































Reviews: